Echo 1-E Скачать руководство пользователя

Страница: 23 / 24

CSG-670 TYPE1-E

Dimensions

Length × Width × Height

730 mm × 250 mm × 360 mm (28.7 in. × 9.8 in. × 14.2 in.)

Mass

(dry mass w/o cutting wheel) 10.8 kg (23.8 lb.)

Engine

Air-cooled, 2-stroke, single cylinder gasoline engine

Displacement

66.8 mL (4.069 cu. in.)

Bore

50.0 mm (1.969 in.)

Stroke

34.0 mm (1.339 in.)

Compression ratio

7.3 : 1

Intake

Piston valve

Carburetor

WALBRO diaphragm type with speed limiter

Ignition system

Flywheel magneto, capacitor discharge ignition type

Spark plug

CHAMPION CJ-8Y

Muffler

Spark arrestor muffler

Throttle control

Throttle trigger with throttle lockout and throttle latch

Fuel tank capacity

650 mL (22.9 US. fl. oz.)

Fuel

Mixed fuel

Fuel oil ratio

50 : 1 (2 %) ratio with ECHO Power Blend™ two-stroke, air-cooled
engine oil

Gasoline

Unleaded regular with minimum Octane of 89. Do not use fuel containing

methyl alcohol or more than 10 % of ethyl alcohol.

Starter system

Automatic rewind starter

Clutch

Centrifugal type

Cutting device

Belt

BANDO ORC 850

Pulley ratio

2 : 1

Belt tensioner

Spring

Cutting wheel

305 mm × 20 mm dia. (12.0 in. × 0.787 in. dia.)
305 mm × 25.4 mm dia. with adapter (12.0 in. × 1.0 in. dia.)

Vibration reduction system

Rubber isolaters mounted between the engine and the handles

Air cleaner

3 stage type: sponge filter, bellows type paper filter and nylon mesh filter

Attachment

Water kit

Option

Cart kit

Option

STORAGE AFTER USE

SPECIFICATIONS

•

Inspect and adjust every part of the cut-off saw.
- Completely clean every part and repair if

necessary.

- Apply thin coating of oil on metal parts to

prevent rust.

•

Remove cutting wheel.

•

Drain fuel tank, pull starter slowly a few times to
drain fuel from carburetor.

•

Pour a small amount of clean motor oil into spark
plug hole, pull starter and crank the engine until
the TOP DEAD CENTER.

•

Store in a dry area, free from dust.

WARNING

Do not store in enclosure where fuel fumes
may accumlate or reach an open flame or
spark.

CAUTION

Do not lend or rent your cut-off saw without the
operator’s manual.

* Technical data subject to change without notice.

NOTE

For future reference, you should keep this
operator’s manual.

If this operator’s manual has become illegible
through impairment or is lost, please purchase
a new one from your ECHO dealer.

Содержание 1-E

























Результаты поиска

Содержание 1-E

Отзывы:

Похожие инструкции для 1-E

Бренды по названию

Популярные бренды

Echo 1-E, Руководство оператора

Результаты поиска

Содержание 1-E

Отзывы:

Похожие инструкции для 1-E

Бренды по названию

Популярные бренды