Echo 001001 - 503999 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

Echo 001001 - 503999 Скачать руководство пользователя страница 18

18

WARNING DANGER

Inspect starting area for hazards such as rocks, glass, debris etc.
which could be contacted by the cutting attachment when starting.
Keep helpers and bystanders at least 15 M (50 ft.) from starting
area, otherwise serious personal injury may result.

4.

Lay the pruner on a flat clear area. With left hand, firmly grasp and
hold throttle trigger lockout lever and throttle trigger in wide open
position. Rapidly pull recoil starter handle (D) until engine fires.

5.

After engine fires, move choke lever back to “Run” position. Hold
throttle trigger fully depressed and pull recoil starter handle until
engine starts and runs. Release throttle trigger and allow unit to
warm up at idle for several minutes.

NOTE
If engine does not start with choke in “Run” position after 4 pulls,
repeat instructions 4 and 5.

6.

After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.

STARTING

WARM

ENGINE

WARNING DANGER

The saw chain should not rotate at idle. If saw chain rotates,
readjust carburetor according to "Carburetor Adjustment" instruc-
tions in this manual or see your dealer, otherwise serious personal
injury may result.

1.

Stop Switch - Start/Run. Move stop switch button (A) forward
away from the STOP position.

2.

Start - Pull Rope. Lay the trimmer on a flat clear area and pull the
recoil starter handle (D) until the engine fires.

NOTE
If engine does not start after 4 pulls, use Cold Start Procedure.

B

D

A

«
...
16
17
18
19
20
...
»

Содержание 001001 - 503999




































Отзывы:

Нет отзывов