Page 1 of 2
Specifications:
Size:
2.96 in. Height
5.12 in. Diameter
Weight:
1.4 lbs.
Voltage:
12-24 VDC
Charging Time: ~4 hours
Installation and Operation Instructions
EB5200 Rechargeable Beacon
Indicator Light:
Operation:
How to resynchronize the lamp and controller?
1. Press the switch on light, within 1 second, press again and hold, until the green
indicator light flashes, then press the on/off on controller, starting pairing.
2.
When the red indicator flashes, press the pattern select button on controller,
finishing pairing.
3.
Now you can switch flash pattern by pressing switch on controller.
Notice:
During the pairing, if the controller is not pressed, light will be back to working
status in 6 seconds.
Prior to use:
1. Fully charge the battery before
first use.
2. The battery should be charged
at least once a month when not in
regular use.
3. Only use the charging cable
provided with this unit.
IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/
or death to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understood the safety information
contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without
losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag
deployment area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death.
Refer to the vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable
mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is the vehicle operator’s responsibility to be sure they can proceed safely before entering an
intersection, drive against traffic, respond at a high rate of speed, or walk on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The
manufacturer assumes no liability for any loss resulting from the use of this warning device.
WARNING!
Risk of fire and burns. Do not open, crush, expose to heat above 120°F(50°C), incinerate or short terminals. Do not store, use or
charge in locations that may reach or exeed 120°F(50°C). Never charge while unattended. Do not expose battery to water or liquids.
Follow manufacturer’s instructions.
WARNING!
Maximum recommended vehicle speed for safe
operation using the Magnet Mount model is 65 mph (104
km/h) on a well maintained road, when fitted to the center of a
vehicle roof of steel construction. Higher speeds could cause
the mount to fail, resulting in the beacon flying off of the vehicle,
which could cause damage to other vehicles and injury or death
to the passengers.
The magnet mount is not intended as a permanent mounting
for the beacon. The magnet mount unit must be mounted on
a magnetic surface (i.e. no fiberglass, etc.). Insure that the
magnet is kept clean.
The Button
1. Long press three seconds ON/OFF
2. Press once to switch flash mode
Indicator Light
Pattern Select
ON/OFF
Charging port
DC 12V/24V
Enhanced magnetic
base
State
Electric quantity
Indicator Light
Charging
status
0-30%
●
Red light
30-99%
●
Yellow light
100%
●
Green light
Discharge
70-100%
●
Green light
30-70%
●
Yellow light
10-30%
●
Red light
10% below
●
Red flash lights