background image

 

GENERAL  INSTRUCTIONS

 

 

SWITCH SETTINGS

 

In order to keep operation easy and straightforward there are only two switches 
on the front panel. 

 

ON/OFF SWITCH

 

The ON/OFF Switch is used to turn on the instrument.  The switch is illuminated, 
and the green light will be 

on 

when the power is turned 

on

.  Remember to turn 

the instrument off when not in use to conserve the batteries. 

 

MODE SWITCH

 

The MODE SWITCH has two functions. 
1. When initially turned on, the instrument can be switched to the 

“High 

Resolution” mode. 
2. After a kVp reading is obtained, pushing the Mode Switch will provide 
additional information. 

 

1. High Resolution / High Speed Modes

 

When the instrument is first powered on, it 

is in “Normal” or “High Speed Mode” 

which is used for most measurements.  When used in Normal Mode the Model 
815 inserts a delay of about 22 milliseconds before measuring the kVp.  Pushing 
the button once will put the instrument into 

“High Resolution Mode”.  In High 

Resolution Mode, the delay is approximately doubled. 

When using the

 

instrument in High Speed Mode, the x-ray exposure time must set to at 
least 40 ms (0.04 sec).  When using the instrument in High Resolution 
Mode, the exposure must be at least 80 ms (0.08 sec).

 

 

When the instrument is put into High Resolution Mode, it will stay in High 
Resolution Mode until it is turned off.  To get the instrument into High Speed or 
Normal mode, turn the power off and then on.  There is additional information 
about using High Resolution Mode in the Operation section. 

 

2. Additional Information Display

 

After a measurement, the kVp value will be displayed.  Additional information can 
be displayed by pushing the mode button momentarily.  The instrument will then 
sequence through the following information: 

•  Waveform Type 

•  Exposure Time in milliseconds 

And back to kVp. 
Waveform type and exposure time will each be displayed for about 1.2 seconds, 
and then the display will revert back to kVp.  After the Additional Information is 
displayed and display returns to kVp, the meter is ready for another reading.  If 
the battery is low, 

a „Batt Low‟ message will also appear for 1.2 seconds. 

Содержание 815















Отзывы: