manualshive.com logo in svg

Ebyte E28-2G4M20S, Руководство пользователя, Страница: 8 / 13

Поделиться
Скачать
Ebyte E28-2G4M20S Скачать руководство пользователя страница 8

Chengdu Ebyte Electronic Technology Co., Ltd.

E28-2G4M20S User

Manual

Copyright ©2012–2021

，

Chengdu Ebyte Electronic Technology Co.,Ltd.

4-7

4.2 Software editing

This module is based on SX1280,same drive way as SX1280,user can refer to SX1280 datasheet.

DIO is general I/O port

，

see more in SX1280 datasheet.

GDO 2 is generally configurated as IRQ function, IRQ pin can also be disconnected. The SPI query mode can be
used to obtain the interrupt status. However, it is recommended to use the external interrupt of the MCU.

After SX1280 restores IDLE mode or configures sleep mode, it is recommended that the power configuration table
be reinitialized.

It is recommended that the power output parameter of SX1280 set to - 2dBm. At this time, the output power of the
module can be 20dBm. When the output power of SX1280 is increased, the current will increase and the power will
not increase significantly.

5.Basic application

5.1 Basic circuit diagram

Содержание E28-2G4M20S














Отзывы:

Нет отзывов