Ebyte E103-W01 Скачать руководство пользователя страница 27

Страница: 27 / 29

Chengdu Ebyte Electronic Technology Co., Ltd.

E103-W01 User Manual

Chengdu Ebyte Electronic Technology Co., Ltd.

11 Production guidance

11.1 Reflow soldering temperature

Profile Feature

Feature

Sn-Pb Assembly

Pb-Free Assembly

Solder Paste

Solder paste

Sn63/Pb37

Sn96.5/Ag3/Cu0.5

Preheat Temperature min

（

Tsmin

）

Min preheating temp.

100℃

150℃

Preheat temperature max (Tsmax)

Max preheating temp.

150℃

200℃

Preheat Time (Tsmin to Tsmax)(ts)

Preheating time

60-120 sec

Average ramp-up rate(Tsmax to Tp)

Average ramp-up rate

3℃/second max

Liquidous Temperature (TL)

Liquid phase temp

183℃

217℃

Time

（

）

Maintained Above

（

）

Time below liquid phase

line

60-90 sec

30-90 sec

Peak temperature

（

）

Peak temp

220-235℃

230-250℃

Aveage ramp-down rate

（

Tp to Tsmax

）

Average ramp-down rate

6℃/second max

Time 25℃ to peak temperature

Time to peak

temperature for 25℃

6 minutes max

8 minutes max

11.2 Reflow soldering curve

Содержание E103-W01






























Результаты поиска

Содержание E103-W01

Отзывы:

Похожие инструкции для E103-W01

Бренды по названию

Популярные бренды

Ebyte E103-W01, Руководство пользователя

Результаты поиска

Содержание E103-W01

Отзывы:

Похожие инструкции для E103-W01

Бренды по названию

Популярные бренды