I
NTRODUCTION
• G
ETTING
S
TARTED
S
PECIFICATIONS
7KH(%6'URPHLVDQXOWUDFRPSDFWDQGXQEHOLHYDEO\OLJKW:EDVV
FRPERZLWKLQFUHGLEOHVRXQGILOOHGZLWKXQLTXHSRVVLELOLWLHV7KHROG9LNLQJ
P\WKVVD\V7RNHHSWKHGLDEROLFDO)HQULVZROIIURPNLOOLQJWKH1RUVH*RGV2GLQ
7KRU)UH\DDQGWKHRWKHUVDQLPSRVVLEO\VWURQJQHFNODFH
'URPH
ZDV
FUHDWHGZKLFKZRXOGNHHSWKHHYLOZROIXQGHUFRQWURO
2
BALANCED OUTPUT:
Output Level
nominal
- 10 dBv
Output Impedance
< 10 ohms current lim.
Frequency Response
+0/-3 dB
35 - 20k Hz
Dynamic Range:
linear
102 dB typ.
A-weighted
105 dB min.
XLR Connections
1-GND, 2-Hot, 3-Cold
Options
Pre/Post EQ,
GND LIFT
EFFECTS LOOP:
Loop Signal Level
nominal
-10 dBv
Gain
Unity (1:1)
Output Impedance (Send)
<100 ohms
Input Impedance (Returns)
47 kohms // 100 pF
Loop Mode
Serial or Parallel
Phantom Power
optional
2 x 10V 20 mA
LINE OUT:
Output Impedance:
< 5 kohms
Nominal Signal Level:
0 dBv
TUNER OUT:
Output Impedance:
< 1 kohms
Signal Level:
Instrument Level
POWERAMP/
Continuous Output Power
150 W RMS
CABINET:
Cabinet:
Impedance
4 ohms
Crossover Freq. 4.5 kHz
Resonance
90 Hz
Volume
28 l
AUXILIARY INFO:
Power Requirements
max
200 W
Mains Protection:
T2A Fuse ( 230V )
T4A Fuse ( 120/100V )
Dimensions:
17" (432 mm) Width
11" (285 mm) Depth
19.8” (502 mm) Height
Weight:
36 lbs. ( 16 kg )
Shipping
40 lbs. ( 18 kg )
References:
0 dBv = 0.775 V RMS
Specifications are subject to change without notice!
19
(%6 'URPH
lU GHQ PHVW NRPSOHWWD
NUDIWIXOODRFKIOH[LEODNRPSDNWDEDVFRPER
VRPQnJRQVLQKDUWLOOYHUNDWV0HGLQE\JJG
VWHUHRPRQLWRUIXQWLRQ VXSHUDNWLYD ILOWHU
RFK GHW NODVVLVND (%6 OMXGHW HUEMXGHU
(%6
'URPH
HQ PlQJG P|MOLJKHWHU VRP
EHVNULYVLGHQQDPDQXDO0HQI|UVWDYDOOW
I|OMHU HQ LQWURGXNWLRQ VRP KMlOSHU GLJ DWW
EOLEHNDQW
(%6'URPH
A
TT KOMMA IGÅNG
...
1. Packa försiktigt upp combon.
2. Se till att alla kontroller är ställda fullt
motsols. Fortsätt med att ställa de tre
filterrattarna märkta BASS, MIDDLE
och TREBLE till mittposition. Leta upp
filteromkopplaren och ställ den i läge
BYPASS. Se även till att omkopplaren
märkt Character är i uttryckt läge. Nu
är ljudet i EBS Drome "nollställt" och
redo för att skapa just ditt personliga
sound.
3. Koppla in din bas.
4. Spela hårt på basen och vrid upp GAIN
ratten tills PEAK dioden börjar blinka.
Än har du inget hörbart ljud, men en
perfekt signal att jobba vidare med.
5. Sök och vrid upp VOLUME ratten till
lämplig ljudnivå.
7KH
(%6 'URPH
LV WKH PRVW SRZHUIXO
YHUVDWLOH DQG FRPSOHWH FRPSDFW EDVV
FRPER HYHU EXLOW :LWK EXLOW VWHUHR
PRQLWRUVHFWLRQDQGDVXSHUSRZHUIXO(4
WKHXQLWRIIHUVDQH[WUHPHO\ZLGHUDQJHRI
SRVVLELOLWLHVZKLOHPDLQWDLQLQJWKDWFODVVLF
(%6 VRXQG 7KHVH EULHI WXWRULDOV ZLOO KHOS
\RX WR EHFRPH DFTXDLQWHG ZLWK VRPH RI
WKHIHDWXUHVRIWKH
(%6'URPH
G
ETTING STARTED
...
1. Carefully unpack the bass combo.
2. Check that the controls are set fully
counter clockwise. Proceed by turning
the three filter knobs marked BASS,
MIDDLE and TREBLE to mid position.
Locate the filter switch and set it to
BYPASS. Make also sure that the
switch marked Character is in its’ outer
position. Now the EBS Drome’s
settings are "zeroed" and ready to be
personalized.
3. Plug in your bass.
4. While plucking the strings as hard as
you would during your hardest playing,
gradually increase the GAIN knob until
the PEAK led starts to flash at peaks.
5. Move over to the VOLUME knob and
adjust for the desired output volume.
