H
C
B
OW TO HANGE ATTERY
1) Carefully remove the four screws holding the bottom plate.
2) Remove the bottom plate gently.
3) Replace the old battery with a new one of the same type, 9V alkaline
type; 6LR61.
4) Gently place back the bottom plate, and make sure no cables are
squeezed. Attach the four mounting screws using moderate tension.
The EBS Phantom Power System™ makes it
possible to power the EBS MultiComp with 9V
DC directly from the EBS Drome, Gorm, Fafner
and 1V2/Classic amps. Here is a step-by-step
instruction on how to do this.
H
EBS P
P
™
OW TO USE THE
HANTOM OWER
1) Connect a stereo ¼” instrument cable (TRS, tip-ring-sleeve) between
the EBS MultiComp pedal and the EBS amp.
2) Activate the phantom power on the amp. This is made with a flick of
a switch on most EBS amps. Please consult the manual for the EBS
amp you are using.
3) Connection done. You should now have power in the pedal, even if
the input jack is left open.
EBS P
P
™ T
S
HANTOM OWER
ROUBLE HOOTING
GND
PH.
SIGNAL
POWER
T
S
G
ROUBLE HOOTING
UIDE
Please consult the following checkpoints, before consulting one of the
authorized EBS service centers.
*EBS Sweden AB guarantees no error free operation when using other
DC adapter than the EBS AD-9. Warranty is void if higher voltage than
9.3 V has been used to feed the EBS MultiComp pedal.
Checkpoint
1) Does the cable(s) work
properly?
2) Are the ¼” plugs properly
connected all the way in?
3) Are the Instrument cable
attached to the Right (input)
jack, and the Amp cable
connected to the Left (output)
jack?
4) Does the pedal have a battery,
and is the battery OK?
5) Does the indicator LED light
when pressing the foot switch
alternatively?
6) Does the instrument work?
7) Does the amplifier work and is
the volume turned up?
8) If you are using a DC adapter,
Are you using an EBS AD-9?
Action if answered NO
- Replace cable(s).
- Push the ¼” plugs all the way in.
- Reconnect input and output jacks.
- Put a new battery in the pedal.
- Replace battery.
- Check the instrument at your
nearest service center.
- Turn up volume or check the amp
at your nearest service center.
- Check the voltage and polarity of
the adapter you are using.*
T
S
EBS M
C
ECHNICAL PECIFICATIONS
ULTI OMP
Nominal Input Level
-10 or -4 dBv
Input Impedance
200 kohms
Bandwidth
+0/-3 dB
20 - 20k Hz
Gain Range
0 - 15 dB
Compressor Ratio
min/max
1:1 - 5:1
Threshold
-25 - +6 dB
(adjustable inside)
Attack Time
(80%)
<10 ms
Release Time
(80%)
typ. 100 ms
Power Requirements
9 V DC Regulated,
15 mA max.
Dimensions
Width
Height
Depth
1.4" (35 mm)
Weight
450g (1 lb.)
2.8" (70 mm)
4.5" (115 mm)
Specifications are subject to change without notice.
EBS Sweden AB · Framnäsbacken 12 · SE-171 66 Solna · Sweden
Phone: +46-8-7350010 · Fax: +46-8-7350015
Web: http://www.ebs.bass.se
E-mail: [email protected]
A
T
O
DVANCED ECHNICAL
PTIONS
(O
A
P
)
NLY FOR UTHORIZED ERSONNEL
ADJUSTING THRESHOLD LEVELS
The EBS MultiComp has the feature of fine-tuning the compressor
thresholds for both the high and low band compressors independently.
The ranges can be set from “off”, which bypasses the desired band, up to a
relative sensitivity of +6 dB from factory setting. These trimmers are set to
50%
from factory.
The trimmers are located on the printed circuit board, and are easily
accessible by removing the bottom plate. When doing any adjustments,
please use a plastic screwdriver, and turn the trimmer gently.
(12 o’clock)
Make sure that the MultiComp operates in MULTIBAND mode when
adjusting the threshold levels.
If you are not 100% sure on how to do this, please
consult your nearest service center. Excessive
force may result in damage to the unit, and the
warranty in that case will be void.
!
Note that only the pedal that is directly connected to the EBS amp can be powered
with phantom power. This means that if you have more than one pedal, ONLY THE
LAST one can use the EBS Phantom Power™.
Checkpoint
1) Is a ¼” STEREO cable used between
the pedal and the amp?
2) Is there power available on the
RING connection of the ¼” plug?
Action if answered NO
- Replace cable to a ¼” STEREO cable.
- Make sure the phantom power is
activated on the amp.
- Check cable.
*EBS recommends the use of the EBS AD-9
, which
supplies a well stabilized power to the EBS MultiComp and all
your other pedals that operate with a 9V battery. The high
current capacity, 650mA, makes it possible to supply all
pedals with only one adapter, EBS AD-9!
DC adapter
UP
DOWN
