background image

Contents 

ii

Copyrights 

©2016 All rights reserved. The information in this 

document is subject to change without prior notice 

in order to improve reliability, design and function 

and does not represent a commitment on the part of 

the manufacturer.   

 

This document contains proprietary information 

protected by copyright.    All rights are reserved.   

No part of this manual may be reproduced by 

any mechanical, electronic, or other means in 

any form without prior written permission of the 

manufacturer.  

 

All trademarks are property of their respective 

owners 

 

Liability Disclaimer 

In no event will the manufacturer be liable for 

direct, indirect, special, incidental, or 

consequential damages arising out of the use or 

inability to use the product or documentation, 

even if advised of the possibility of such 

damages.  

 

Regulatory Information 

FCC Notices   

 

This equipment has been tested and found to 

comply with the limits for a Class A digital 

device, pursuant to Part 15 of the Federal 

Communications Commission (FCC) Rules. 

These limits are designed to provide reasonable 

protection against harmful interference in a 

residential installation. This equipment 

generates, uses, and can radiate radio 

frequency energy and, if not installed and used 

in accordance with the instructions, may cause 

harmful interference to radio communications. 

However, there is no guarantee that 

interference will not occur in a particular 

installation. If this equipment does cause 

harmful interference to radio or television 

reception, which can be determined by turning 

the equipment off and on, the user is 

encouraged to try to correct the interference by 

one or more of the following measures: 

• Increase the separation between the 

equipment and the receiver. 

• Connect the equipment into an outlet on a 

circuit different from that to which the receiver is 

connected. 

• Consult the dealer or an experienced radio or 

television technician for help. 

This device complies with Part 15 (A) of the 

FCC Rules. Operation is subject to the following 

two conditions:   

1) this device may not cause harmful 

interference and   

2) this device must accept any interference 

received, including interference that may cause 

undesired operation. 

NOTE: THE MANUFACTURER IS NOT 

RESPONSIBLE FOR ANY RADIO OR TV 

INTERFERENCE CAUSED BY 

UNAUTHORIZED MODIFICATIONS TO THIS 

DEVICE. SUCH MODIFICATIONS COULD 

VOID THE USER'S AUTHORITY TO 

OPERATE THE DEVICE.

 

 

CE Notice 

 

This device complies with 

EMC Directive 

2004/108/EC

 issued by the Commission of the 

European Community. 

Содержание DNPOS70P-5BTH-N3700
























Отзывы: