Operating instructions
S4D350-BA06-08
Translation of the original operating instructions
3.2 Nominal data
Motor
M4D068-EC
Phase
3~
3~
3~
3~
Nominal voltage / VAC
230
230
400
400
Wiring
Δ
Δ
Y
Y
Frequency / Hz
50
60
50
60
Method of obtaining
data
fa
fa
fa
fa
Valid for approval/
standard
-
-
-
-
Speed (rpm) / min
-1
1420
1620
1420
1620
Power consumption / W
145
190
145
190
Current draw / A
0.68
0.62
0.39
0.36
Max. back pressure / Pa
150
150
150
150
Min. ambient
temperature / °C
-25
-25
-25
-25
Max. ambient
temperature / °C
50
50
50
50
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
Actual
Req. 2015
01 Overall efficiency η
es
/ %
31.3
28.7
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
42.6
40
05 Variable speed drive
No
06 Year of manufacture
The year of manufacture is specified on the
product's rating label.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
08 Type
S4D350-BA06-08
09 Power consumption P
e
/ kW
0.16
09 Air flow q
v
/ m³/h
2005
09 Pressure increase total p
sf
/
Pa
92
10 Speed (rpm) n / min
-1
1390
11 Specific ratio
*
1.00
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
3.4 Technical description
Weight
4.2 kg
Size
350 mm
Motor size
68
Rotor surface
Painted black
Terminal box material
ABS plastic
Blade material
Sheet steel, painted black
Guard grille material
Steel, coated with black plastic (RAL
9005)
Number of blades
5
Airflow direction
A
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
as per EN 60034-5
Insulation class
"B"
Moisture (F) /
Environmental (H)
protection class
H1+
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
On rotor side
Mode
S1
Motor bearing
Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
< 0.75 mA
Electrical hookup
Terminal box; Capacitor integrated and
connected
with cable
Axial
Protection class
I (with customer connection of protective
earth)
Conformity with
standards
EN 60335-1, motor does not have
factory-installed overheating protection
Approval
EAC; CCC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
Item no. 14783-5-9970 · ENU · Change 207534 · Approved 2019-12-14 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com