ebm-papst S4D300-AS34-37 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 10

ebm-papst S4D300-AS34-37 Скачать руководство пользователя страница 7

Operating instructions

S4D300-AS34-37

Translation of the original operating instructions

4.3.3 Cable routing

No water may penetrate along the cable in the direction of the cable gland.

Fans installed lying flat

Make sure that the cable is routed in the form of a loop (water trap).

Fig. 2: Fan installed lying flat, cable routed as a water trap.

Fans installed in upright position

When routing the cable, ensure that the screwed cable glands are
arranged at the bottom. The cables must always be routed downwards.

Fig. 3: Cable routing for fans installed upright.

4.3.4 Motor protection

WARNING
Device without overheating protection

The device is delivered without any automatically functioning
overheating protection. The device can become hot and burn.
→ For the version without TOP, install an additional, suitable

motor protection switch.

Item no. 12198-5-9970 · Revision 76115 · Release 2012-02-23 · Page 7 / 10

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

«
...
5
6
7
8
9
...
»

Содержание S4D300-AS34-37











Отзывы:

Нет отзывов