ebm-papst K3G630-PW04-01 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 13

ebm-papst K3G630-PW04-01 Скачать руководство пользователя страница 4

Operating instructions

K3G630-PW04-01

Translation of the original operating instructions

3. TECHNICAL DATA

3.1 Product drawing

All dimensions in mm.

1

Inlet ring with pressure tap (k-factor: 438)

2

Mounting position for vibration-absorbing elements, tightening torque max. 40 Nm

3

Cable diameter min. 5 mm, max. 13 mm; tightening torque 6 ± 0.9 Nm

4

Cable diameter min. 16 mm, max. 20.5 mm, tightening torque 6 ± 0.9 Nm

5

Tightening torque 3.5 ± 0.5 Nm

6

Attachment holes for FlowGrid (00630-2-2957 not included in scope of delivery)

7

Motor support plate
Installation position: Only base mounting, shaft horizontal (motor support plate must be vertical!).
Rotor on top or rotor on bottom on request
The drawing shows the dimensions only and does not represent the installation position

Item no. 55797-5-9970 · ENU · Change 277818 · Approved 2023-04-27 · Page 4 / 13

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

«
...
2
3
4
5
6
...
»

Содержание K3G630-PW04-01














Отзывы:

Нет отзывов