Operating instructions
G2E180-EH03-01
Translation of the original operating instructions
3.2 Nominal data
Motor
M2E074-EI
Phase
1~
1~
Nominal voltage / VAC
230
230
Frequency / Hz
50
60
Type of data definition
fa
ml
Valid for approval /
standard
CE
CE
Speed (rpm) / min
-1
1950
2150
Power input / W
400
415
Current draw / A
1.75
1.82
Motor capacitor / µF
8
8
Capacitor voltage / VDB
400
400
Capacitor standard
S0 (CE)
S0 (CE)
Min. back pressure / Pa
0
250
Min. ambient
temperature / °C
-25
-25
Max. ambient
temperature / °C
40
30
Starting current / A
2.2
2
ml = Max. load · me = Max. efficiency · fa = Running at free air
cs = Customer specs · cu = Customer unit
Subject to alterations
3.3 Data in accordance with ecodesign regulation EU 327/
2011
Actual
Request 2015
01 Overall efficiency η
es
/ %
35.3
33.7
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
45.6
44
05 Variable speed drive
No
06 Year of manufacture
The year of manufacture is specified on the
rating plate on the product.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
County court Stuttgart · HRA 590344
D-74673 Mulfingen
08 Type
G2E180-EH03-01
09 Power input P
e
/ kW
0.23
09 Air flow q
v
/ m³/h
460
09 Pressure increase total p
fs
/
Pa
653
10 Speed (rpm) n / min
-1
2680
11 Specific ratio
*
1.01
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data definition with optimum efficiency. The ErP data is determined using a motor-impeller
combination in a standardised measurement configuration.
3.4 Technical features
Mass
5.3 kg
Size
180 mm
Motor size
74
Surface of rotor
Coated in black
Material of impeller
Sheet steel, coated in black
Housing material
Die-cast aluminium
Direction of rotation
Clockwise, seen on rotor
Type of protection
IP44; Depending on installation and
position as per EN 60034-5
Insulation class
"B"
Humidity (F) /
environmental
protection class (H)
H0 - dry environment
Mounting position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
Rotor-side
Operation mode
S1
Motor bearing
Ball bearing
Touch current acc.
IEC 60990 (measuring
network Fig. 4, TN
system)
< 0.75 mA
Motor protection
Thermal overload protector (TOP) wired
internally
Protection class
I (if protective earth is connected by
customer)
Product conforming
to standard
EN 60335-1; CE
Approval
CCC; EAC
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
;
Use the device in accordance with its protection type.
Notes on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may vary during the production period.
Strength, dimensional stability and dimensional accuracy are not affected
by this.
The colour pigments of the paints used react perceptibly to UV light over
the course of time. To prevent the formation of patches and fading, the
product is to be protected against UV radiation. Changes in colour are
not a reason for complaint and are not covered by the warranty. UV
radiation in the frequency range and the intensity of natural solar radiation
has no effect on the technical properties of the products.
3.5 Mounting data
Any further mounting data required can be taken from the product
drawing or Section chapter 4.1 Connecting the mechanical system.
Strength class for
mounting screws
8.8
For depth of screw, see chapter 3.1 Product drawing
;
Secure the mounting screws against accidentally coming loose (e.g.
by using self-locking screws).
Item no. 10294-5-9970 · ENG · Revision 212114 · Release 2020-03-10 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com