Operating instructions
G2D160-AF12-03
Translation of the original operating instructions
3.2 Nominal data
Motor
M2D068-EC
Phase
3~
3~
3~
3~
Nominal voltage / VAC
400
400
400
400
Wiring
Δ
Y
Δ
Y
Frequency / Hz
50
50
60
60
Method of obtaining
data
fa
fa
ml
ml
Valid for approval/
standard
CE
CE
CE
CE
Speed (rpm) / min
-1
2200
1350
2600
1650
Power consumption / W
320
160
305
155
Current draw / A
0.48
0.24
0.46
0.24
Min. back pressure / Pa
0
0
400
155
Min. ambient
temperature / °C
-40
-40
-40
-40
Max. ambient
temperature / °C
55
55
50
50
Starting current / A
0.95
0.35
0.9
0.32
Phase
3~
3~
Nominal voltage / VAC
480
480
Wiring
Δ
Y
Frequency / Hz
60
60
Method of obtaining
data
ml
ml
Valid for approval/
standard
CE
CE
Speed (rpm) / min
-1
2900
1950
Power consumption / W
340
200
Current draw / A
0.45
0.26
Min. back pressure / Pa
500
230
Min. ambient
temperature / °C
-40
-40
Max. ambient
temperature / °C
50
50
Starting current / A
1.0
0.38
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
4 kg
Size
160 mm
Motor size
68
Rotor surface
Painted black
Impeller material
Sheet steel, galvanized
Housing material
Die-cast aluminum
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP44
Insulation class
"F"
Moisture (F) /
Environmental (H)
protection class
H1+
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
On rotor side
Mode
S1
Motor bearing
Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
< 0.75 mA
Motor protection
Thermal overload protector (TOP) with
basic insulation
Protection class
assignment
I; If a protective earth is connected by
the customer
This component for installation may
have several local protection classes.
This information relates to this
component’s basic design.
The final protection class is based on
the component’s intended installation and
connection.
Conformity with
standards
EN 50155: 2008; EN 61373, Cat. 1B:
2010; EN 45545-2, HL3: 2013 +
A1:2015; CE
Approval
EAC
Comment
Prerequisite for operation is a Class 1
vehicle electrical system architecture
according to EN 50533
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.
3.4 Mounting data
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
screws
8.8
For screw clearance, see Chapter 3.1 Product drawing
;
Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Item no. 16624-5-9970 · ENU · Change 251972 · Approved 2022-02-16 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com