Operating instructions
G2D140-AC38-03
Translation of the original operating instructions
3.2 Nominal data
Motor
M2D068-DF
Phase
3~
3~
3~
3~
Nominal voltage / VAC
400
400
400
400
Wiring
Δ
Y
Δ
Y
Frequency / Hz
50
50
60
60
Method of obtaining
data
fa
fa
fa
fa
Valid for approval/
standard
CE
CE
CE
CE
Speed (rpm) / min
-1
2300
1600
2350
1500
Power consumption / W
145
80
190
90
Current draw / A
0.22
0.13
0.29
0.14
Min. ambient
temperature / °C
-40
-40
-40
-40
Max. ambient
temperature / °C
80
80
80
80
Starting current / A
0.55
0.19
0.5
0.18
Phase
3~
3~
Nominal voltage / VAC
480
480
Wiring
Δ
Y
Frequency / Hz
60
60
Method of obtaining
data
fa
fa
Valid for approval/
standard
CE
CE
Speed (rpm) / min
-1
2650
1750
Power consumption / W
225
120
Current draw / A
0.29
0.15
Min. ambient
temperature / °C
-40
-40
Max. ambient
temperature / °C
80
80
Starting current / A
0.65
0.22
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
3.5 kg
Size
140 mm
Motor size
68
Rotor surface
Painted black
Impeller material
Sheet steel, galvanized
Housing material
Die-cast aluminum
Guard grille material
Hot-dip galvanized and spot-welded net
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
as per EN 60034-5
Insulation class
"F"
Moisture (F) /
Environmental (H)
protection class
H1+
Installation position
Any
Condensation
drainage holes
On rotor side
Mode
S1
Motor bearing
Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
< 0.75 mA
Motor protection
Thermal overload protector (TOP) with
basic insulation
with cable
Axial
Protection class
I (with customer connection of protective
earth)
Conformity with
standards
EN 45545-2 + A1:2015; EN 50155:
2008; EN 61373, Cat. 1B: 2010
Approval
EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.
3.4 Mounting data
Further mounting data can be taken from the product drawing or Chapter
4.1 Mechanical connection as required.
Strength class of
screws
8.8
For screw clearance, see Chapter 3.1 Product drawing
;
Secure the screws against unintentional loosening (e.g. use self-
locking screws).
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
+80 °C
Min. permitted
ambient temp. for
motor (transport/
storage)
-40 °C
Item no. 16623-5-9970 · ENU · Change 257119 · Approved 2023-02-03 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com