ebm-papst D2E146-HT75-45 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 11

ebm-papst D2E146-HT75-45 Скачать руководство пользователя страница 7

Operating instructions

D2E146-HT75-45

Translation of the original operating instructions

For operation with variable frequency drives, install sinusoidal
filters that work on all poles (phase-phase and phase-ground)
between the drive and the motor.
During operation with variable frequency drives, an all-pole
sine filter protects the motor against high-voltage transients that
can destroy the coil insulation system, and against harmful
bearing currents.

Heating-up of the motor when using a variable frequency drive must be
checked by the customer following installation in the end device.

4.3 Plug connection

4.3.1 Making supply connections

;

Check your connector's pin assignment.

;

Connect the built-in connector with the mating connector.

;

Ensure that the connector is properly engaged.

Item no. 16535-5-9970 · ENU · Change 208759 · Approved 2021-02-10 · Page 7 / 11

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

«
...
5
6
7
8
9
...
»

Содержание D2E146-HT75-45












Отзывы:

Нет отзывов