Operating instructions
A4D500-AM03-01
Translation of the original operating instructions
3.2 Nominal data
Motor
M4D110-GF
Phase
3~
3~
3~
3~
Nominal voltage / VAC
400
400
400
460
Connection
Δ
Y
Δ
Δ
Frequency / Hz
50
50
60
60
Type of data definition
ml
ml
ml
ml
Valid for approval /
standard
CE
CE
CE
CE
Speed (rpm) / min
-1
1390
1180
1590
1640
Power input / W
720
550
1020
1060
Current draw / A
1.41
0.9
1.7
1.64
Max. back pressure / Pa
140
100
130
138
Min. ambient
temperature / °C
-40
-40
-40
-40
Max. ambient
temperature / °C
65
65
50
60
Starting current / A
6.5
2.2
5.9
6.8
ml = Max. load · me = Max. efficiency · fa = Running at free air
cs = Customer specs · cu = Customer unit
Subject to alterations
3.3 Data in accordance with ecodesign regulation EU 327/
2011
Actual
Request 2015
01 Overall efficiency η
es
/ %
35.2
32.7
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
42.5
40
05 Variable speed drive
No
06 Year of manufacture
The year of manufacture is specified on the
rating plate on the product.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
County court Stuttgart · HRA 590344
D-74673 Mulfingen
08 Type
A4D500-AM03-01
09 Power input P
e
/ kW
0.7
09 Air flow q
v
/ m³/h
6165
09 Pressure increase total p
sf
/
Pa
146
10 Speed (rpm) n / min
-1
1390
11 Specific ratio
*
1.00
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data definition with optimum efficiency. The ErP data is determined using a motor-impeller
combination in a standardised measurement configuration.
3.4 Technical features
Mass
9.4 kg
Size
500 mm
Motor size
110
Surface of rotor
Coated in black
Material of terminal box
PP plastic
Material of blades
Press-fitted sheet steel blank, sprayed
with PP plastic
Number of blades
5
Direction of air flow
V
Direction of rotation
Counter-clockwise, seen on rotor
Type of protection
IP54
Insulation class
"F"
Humidity (F) /
environmental
protection class (H)
H2
Note ambient
temperature
Occasional start-up between -40 °C and -
25 °C is permissible. For continuous
operation at ambient temperatures below -
25 °C (e.g. refrigeration applications), a
fan version with special low-temperature
bearings must be used.
Mounting position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
Rotor-side
Operation mode
S1
Motor bearing
Ball bearing
Touch current acc.
IEC 60990 (measuring
network Fig. 4, TN
system)
<= 3.5 mA
Electrical connection
Terminal box
Motor protection
Thermal overload protector (TOP)
brought out, basic insulation
Cable exit
Axial
Protection class
I (if protective earth is connected by
customer)
Product conforming
to standard
EN 60034-1 (2010); CE
Approval
EAC; CCC; VDE
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
;
Use the device in accordance with its protection type.
Notes on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may vary during the production period.
Strength, dimensional stability and dimensional accuracy are not affected
by this.
The colour pigments of the paints used react perceptibly to UV light over
the course of time. This does not however have any influence on the
technical properties of the products. To prevent the formation of patches
and fading, the product is to be protected against UV radiation. Changes
in colour are not a reason for complaint and are not covered by the
warranty.
Item no. 10057-5-9970 · ENG · Revision 98149 · Release 2020-10-01 · Page 5 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
