background image

Operating instructions

K3G400-PA27-62

Translation of the original operating instructions

Impeller not
running smoothly

Imbalance in rotating
parts

Clean the device;
replace it if imbalance
persists after cleaning.
Make sure no
weight clips are
removed during
cleaning.

Motor not turning

Mechanical blockage

Switch off, isolate
from supply and
remove mechanical
blockage.

Line voltage faulty

Check line voltage,
restore power supply.
Attention! The error
message resets
automatically.
Device restarts
automatically without
warning.

Faulty connection

Isolate from supply,
correct connection;
see connection
diagram.

Broken motor winding Replace device
Inadequate cooling

Improve cooling.
Allow the device to
cool down.

Ambient temperature
too high

Reduce the ambient
temperature. Allow
the device to cool
down.

Impermissible
operating point (e.g.
back pressure too
high)

Correct the operating
point. Allow the
device to cool down.

In the event of further malfunctions, contact ebm-papst.

6.1 Warning/status codes

The LED on the electronics housing shows the motor status with various
colors and flash codes. The flash codes have a frequency of 2 Hz.
Each flash code is followed by a pause lasting 3 seconds. The following
colors are used: Green: no warning or fault. Orange: There is a warning.
No user intervention is required for warnings. Red: There is at least one
error. See the following table. If there are multiple simultaneous errors,
their associated flash codes are displayed in succession. If there are
simultaneous warnings and errors, only the errors are displayed.

Number of
pulses

Motor
status -
LED red

Manual
reset
required

Possible
cause

Possible
remedy

1

Phase
failure or
line
undervoltage

no

Missing
phase
Poor grid
quality

Check line
voltage

3

Output
stage
overheating.

yes

Dirty
electronics
housing.

Improve
cooling.

4

Communication
error
between
master
controller
and slave
controller

no

External
supply
applied via
Vout for
setting
parameters.
Internal
error.

Switch off
line voltage
- wait
- switch
back on.

6

Motor
overheating

yes

Ambient
temperature
too high.
Impermissible
operating
point.

Lower the
ambient
temperature.
Correct
the
operating
point.

7

Hall sensor
fault

yes

Internal error Switch off

line voltage
- wait
- switch
back on.

8

Motor
blocked

no

Mechanical
blockage

Switch off
- Verify
isolation
from supply
- Check
rotor
freedom of
movement.

9

Speed limit
exceeded

no

-

-

11

Rotor
position
sensor
calibration
error

no

Follow the
replacement
instructions

Rotor
position
sensor
needs
calibration.
Notify
ebm-papst.

13

DC-link
undervoltage

no

Line
voltage faulty

Check
applied line
voltage on
fan.

6.2 Vibration testing

Checking of fan for mechanical vibration based on ISO 14694.
Recommendation: Every 6 months. Max. vibration severity is 3.5 mm/
s, measured at the motor fastening diameter on the motor support plate in
the direction of the motor axis of rotation and perpendicular to this.

Item no. 56960-5-9970 · ENU · Change 200100 · Approved 2019-01-24 · Page 13 / 15

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

Содержание K3G400-PA27-62
















Отзывы: