background image

EBARA

 Pumps Americas Corporation 

www.pumpsebara.com

26 

(t) 803  327-5005  •  (f) 803  327-5097

rev. 01/14 

EBARA Oil Smart Pump System

1. Inspection: Your system has been carefully packaged to prevent damage during  

    shipping. However, occasional damage does occur due to rough handling. Carefully  
    inspect all parts of the system that could cause it to fail. 

2. Refer to the pump installation instructions on page 9 to begin. After completing the  

    pump installation steps, continue here.  

3. Caution: To maintain the NEMA 4X rating, make all wiring connections with seal tight  

    cable grips or conduit connections to be supplied by end user.  

4.  Determine mounting location for control panel. Mount panel using mounting feet supplied.  
5.  Determine hole location on panel for liquid-tight or conduit connections. Attach connectors  

    and conduits. 

6. It is important that the alarm circuit is independent of the pump to assure that the  

    alarm will activate if pump circuit fails. 

7. Run pump cable, Liquid Smart® cable, and Oil Smart® cable through conduit. Make  

    field connections as shown on wiring diagram (See page XX). 

8. Run power line conductor through conduit. Wire to terminals per enclose schematic.  

    Branch circuit protection to be provided by end-user. 

9. For 1-1/2‰ pipe: Attach the Oil Smart® Pump Switch and Oil Smart® Liquid Alarm  

    Switch to the Quick Mount Brackets using the screws and nuts provided. Snap the  
    pump switch bracket onto the discharge pipe with the end of the long sensor 2‰  
    above the top of the pump. Snap the alarm bracket onto the discharge pipe with sensor  
    end 2‰ above the pump switch „on‰ position. Place hose clamps under the quick  
    mount brackets as a reference locator for the switch. Mount switches clear of the  
    basin inlet, so they will stay clean. Note: Keep sensors 1‰ to 2‰ away from any metallic  
    material. 

10.    For other than 1-1/2‰ pipe: Attach the Oil Smart® Pump Switch and Oil Smart®  

    Liquid Alarm Switch to the universal bracket. Place the supplied hose clamp through  
    the slots in the bracket before mounting the switch with the screws and nuts provided.  
    Clamp the Oil Smart® Pump Switch to the discharge pipe with the end of the long  
    sensor 2‰ above the top of the pump. Attach the Oil Smart® Liquid Alarm Switch onto  
    the discharge pipe with the sensor end 2‰ above the pump switch „on‰ position.  
    Mount switches clear of the basin inlet, so they will stay clean. Note: Keep sensors 1‰  
    to 2‰ away from any metallic material. 

 
Start up: 
1. When the power is applied, the red power light locate on the white front swing panel  

    shall light. 

2. The Pump HOA Switch shall be placed to the A (auto) position to ensure the system  

    will pump. The pump can be tested or turned on manually if the HOA switch is in the H  
    (Hand-Manual) position. 

 
To test the alarm circuit, push the test button on the front panel, the audible alarm shall 
sound and the high red beacon will light. 
 
Service: 
Caution: Before checking electrical connections within the control or attempting to replace 
any components, turn off all branch circuits supplying power to the main control panel.

Oil Smart

®

 Pump System – Installation Instructions

Содержание Oil Smart ESS100































Отзывы: