EAW UX48 series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 23

EAW UX48 series Скачать руководство пользователя страница 15

UX48 Owners Manual

15

12. Power Inlet–

The EAW UX48 unit should be connected to a suitable mains electricity supply using a grounded IEC C14

connection power lead. The processor has a switch mode power supply that is capable of operating with a nominal mains voltage
of 100V to 230V, 50/60Hz without re-configuration.

NOTE:

The UX48 must be grounded to a suitable power earth; failure to do so may affect performance and/or operation and will

invalidate warranty and could be potentially hazardous.

13. Dante Audio Ports–

Used to connect to Dante network. Can be configured for switched or redundent operation.

14. Ethernet Communications Port–

Used for remote control and monitoring via Resolutio Software.

15. Auxiliary Port–

The auxiliary port may be configured for a variety of purposes. See the

AUXA Port

section

.

16. AES Digital Audio Output Connectors–

The processed outputs are impedance balanced, and wired: pin-1 directly bonded to

ground (as required by the AES48 standard), pin-2 hot and pin-3 cold. When AES3 operation is selected on an output pair, the Odd
channel connector is used for both channels (e.g. Input 1 is used for channels 1 and 2).

17. AES Digital Audio Input Connectors–

All audio connections are fully balanced and wired: pin-1 to ground (as required by the

AES48 standard), pin-2 hot & pin-3 cold. When AES3 operation is selected on an input pair, the Odd channel connector is used for
both channels (e.g. Input 1 is used for channels 1 and 2).

12

13

14

15

16

17

«
...
13
14
15
16
17
...
»

Содержание UX48 series
























Отзывы:

Нет отзывов