Basic Mode Card
3. Delete connections selectively
Delete an assigned pushbutton
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator enters teach-in mode,
the LED in the actuator is on
2. Press the selected pushbutton until the LED has flashes 5 times
3. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Delete an assigned pushbutton on the remote control
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 => actuator enters teach-in mode, the
LED in the actuator is on
2. Press the selected preselection button (1-6) and then the selected pushbutton (left or. right rocker) until the LED
has flashed 5 times
3. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Delete assigned room controller
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 => actuator enters teach-in mode, the
LED in the actuator is on
2. Set the control wheel to position „-“
3. Wait until the LED on the actuator has flashed 5 times to indicate that the connection has been deleted
4. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Delete assigned channel of the binary input in switch mode
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 => actuator enters teach-in mode, the
LED in the actuator is on
2. Open contact of the binary input
3. Wait until the LED in the actuator has flashed 5 times
4. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Delete assigned channel of the binary input in push button
mode
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 => actuator enters teach-in mode, the
LED in the actuator is on
2. Press pushbutton on the contact of the binary input until LED has flashed 5 times
3. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
4. Reset actuator
Reset actuator
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 => actuator enters teach-in mode, the
LED in the actuator is on
2. Press the configuration pushbutton with a screwdriver until LED has flashed 5 times
3. The actuator leaves teach-in mode automatically after some seconds
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
2. Make connection
Assign a pushbutton to an actuator
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator enters teach-in mode
LED in the actuator is on
2. Press the selected pushbutton shorter than 0,5 sec
3. LED in the actuator flashes twice for confirmation
4. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Assign remote control to an actuator
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator enters teach-in mode,
the LED in the actuator is on
2. Press the selected preselection button (1-6) and then the selected pushbutton (left or. right rocker) shorter than
0,5 sec
3. The LED in the actuator flashes twice for confirmation
4. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Assign a room thermostat to an actuator
1. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator enters teach-in mode,
the LED in the actuator is on
2. Turn the control knob to +
3. The LED in the actuator flashes twice for confirmation
4. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Assign a channel of the binary input in switch mode
1. Press the configuration button on the binary input (the mains supplied version requires a srewdriver) for selecting
the mode, switch mode is Mode 2, LED flashes 2x for Mode 2
2. Open contact of the binary input
3. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator enters teach-in mode, the
LED in the actuator is on
4. Close contact of the binary input
5. The LED in the actuator flashes twice for confirmation
6. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
Assign a channel of the binary input in push button mode
1. Press the configuration button on the binary input (the mains supplied version requires a srewdriver) for selecting
the mode, push button mode is Mode 1, LED flashes 1x for Mode 1
2. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator enters teach-in mode, the
LED in the actuator is on
3. Press pushbutton on the contacts of the binary input shorter than 0,5 sec
4. The LED in the actuator flashes twice for confirmation
5. Press the configuration pushbutton with a screwdriver shorter than 0,5 sec => actuator leaves teach-in mode
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
CSAU-01/01
CJAU-01/01
CDAU-01/01
CTAA-01/01
CTAA-02/01
CRCA-00/01
CHSZ-00/01
CBEU-02/01
CBEU-02/02
Basic Mode Card
7
6
Содержание xComfort
Страница 1: ...xComfort Technical Information...
