Eaton TRTS4400 Скачать руководство пользователя страница 9

Страница: 9 / 46

Diagnostic Procedure

iagnostic Pr

ocedur

Vehicle Electrical Pretest

Step A

•

Key Off

•

Remove chassis interface connector (J1) from transmission control module and use a Volt Ohm-Meter to measure
resistance between Battery (-) Negative pins 7 and 8 and Negative Battery Post.

•

If battery (-) negative pin 7 and 8 reading is between 0 and 1 ohms, continue to Step B.

•

If the reading is outside of range, repair ground supply according to OEM guidelines. Repeat Step A to verify
ground supply.

Step B

•

Key On

•

From the (J1) connector use a Volt Ohm-Meter to measure voltage between Vehicle Ignition pin 6 and Battery (-) Nega-
tive pins 7 and 8.

•

If voltage is between 11 and 13 volts on a 12-volt system, or 22 to 26 on a 24-volt system, continue to Step C.

•

If voltage is outside of range, repair Vehicle Ignition voltage supply according to OEM guidelines. Repeat Step B to
verify Ignition voltage supply.

Step C

•

Key On

•

From the (J1) connector use a Volt Ohm-Meter to measure voltage battery between Battery Positive pin 5 and Battery
(-) Negative pins 7 and 8.

•

If voltage is between 11 and 13 volts on a 12-volt system, or 22 and 26 volts on a 24-volt system, test complete.

•

If voltage is outside of range, repair Battery Positive voltage supply according to OEM guidelines. Repeat Step C to
verify Battery Positive voltage.

Содержание TRTS4400















































Результаты поиска

Содержание TRTS4400

Отзывы:

Похожие инструкции для TRTS4400

Бренды по названию

Популярные бренды

Eaton TRTS4400, Руководство по устранению неисправностей

Результаты поиска

Содержание TRTS4400

Отзывы:

Похожие инструкции для TRTS4400

Бренды по названию

Популярные бренды