manualshive.com logo in svg

Eaton Power Xpert 9395, Руководство по установке

Поделиться
Скачать
Eaton Power Xpert 9395 Скачать руководство пользователя страница 43

Power Xpert 9395 Integrated Battery Cabinet (Model 1085 and 1085HR) Installation Manual  

S

  164201687 Rev 4

    www.eaton.com/powerquality

5-1

Chapter 5

Oneline Drawings and Schematics

5.1

Oneline Drawings

Figure 5‐1 through Figure 5‐4 show the battery cabinet oneline drawings.

UPS Cabinet

Four Cabinets Maximum

Battery Cabinet

Battery Cabinet

Battery Cabinet

Battery Cabinet

NOTE  

See paragraph 3.2.2 for wiring installation notes and Table 3‐3 for wiring requirements.

(E4)

(E5)

I/O

Figure 5‐1. Battery Cabinet Oneline – Common Battery (275 and 500 kVA RT and 275 kVA Plus 1 UPS)

UPS Cabinet

Four Cabinets Maximum

Battery Cabinet

Battery Cabinet

Battery Cabinet

Battery Cabinet

NOTE  

See paragraph 3.2.2 for wiring installation notes and Table 3‐3 for wiring requirements.

Battery Disconnect

(E4)

(E5)

I/O

Figure 5‐2. Battery Cabinet Oneline with Disconnect – Common Battery (275 and 500 kVA RT and 275 kVA Plus 1 UPS)

Figure 

Содержание Power Xpert 9395

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды