Eaton HMIVU07CUNBE Скачать руководство пользователя | Manualshive

Страница: 1 / 16

background image

1

Remote Annunciator
Controller (RAC)
Instruction Sheet for
ATC-900 Controllers

Revision: 006

IB140010EN

Overview

1.0

The 7” RAC is a color touch-screen display with easy-to-use functions that provide a
powerful interface with up to 8 Automatic Transfer Switches equipped with the ATC-
900 controller. It supports serial RS-485 Modbus RTU and Modbus TCP/IP natively.
When using Ethernet to connect to an ATC-900, a serial-to-Ethernet Modbus gateway
is required such as the PXG-900 or the ELC-CAENET.

The 7” RAC Kit contains the following:

HMIVU07CUNBE (7” Color HMI Display)
IL04801003E (HMI Instruction Leaflet)
IB01602080E (Ethernet Setup Document)
ELC-PS01 or 02 (Optional 24VDC power supply)
IB140010EN (This Instruction Sheet)
66A8395, E, or EM (HMI Wiring Diagram)
66A8448H02 (HMI Interconnect Module – serial connections only)

1
2
3
...
»

Содержание HMIVU07CUNBE

















Отзывы:

Нет отзывов

Похожие инструкции для HMIVU07CUNBE

Бренд: BADLANDS Страницы: 2

Бренд: Yudian Страницы: 26

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

Бренд: Absima Страницы: 5

Бренд: Rain Bird Страницы: 48

Бренд: Sullair Страницы: 31

Saxun Mosquito Screen Lateral Door 2020

Бренд: Gimenez Ganga Страницы: 2

Бренд: Keysight Technologies Страницы: 78

Бренд: ACTi Страницы: 20

Бренд: SOARNEX Страницы: 14

Бренд: Tristan Auron Страницы: 30

Бренд: Pestill Страницы: 4

Бренд: FEAM Страницы: 14

Бренд: EasyCare Страницы: 26

Бренд: CommBox Страницы: 4

Бренд: RDL Страницы: 2

Бренд: Vector Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды