INS #
Installation Instructions
Model# CK4A-SSRC
Model# CK4A-SLRC
Model# CK4A-STPRC
ControlKeeper® 4A
General Information
The ControlKeeper 4A model is shipped in one package
and is configured with a dual tapped 120V/277V/347V
60 Hz or 230V/240V 50 Hz transformer. It can be
configured with different relay types as needed to achieve
lighting needs. Please refer to your order information to
determine which model you have purchased.
The ControlKeeper 4A can control up to four relays per
panel with optional support for up to four 0-10V dimming
control outputs to allow for combinations of relay
switching and load dimming.
Getting Started
1. Do not discard these installation instructions. Please
keep for future reference and operation information.
2. Always disconnect all power before wiring.
3. Use only as intended and at the listed voltage.
4. All installation and service must be performed by
qualified personnel or service technicians.
5. Install in accordance with the National Electrical Code
and any other codes which may apply.
6. Installation and wiring information contained in this
document is based on industry-accepted standards
and practices. If conflicts exist between these
instructions and any applicable codes or ordinances,
please contact Greengate before proceeding with the
installation.
7. High voltage is present inside the enclosure. Use
extreme caution when performing maintenance on
this equipment. Failure to follow this warning and
proper safety procedures could result in severe injury
or death, and/or damage to the equipment.
8. Document all wiring and device terminations and
locations so that devices can be properly configured
and programmed for operation.
Mounting the Cabinet
1. Choose a dry location on a firm surface convenient to
the circuits being controlled. Allow full clearance for
the door of the enclosure to open fully.
2. Mount the ControlKeeper 4A cabinet using the holes
provided in the back of the enclosure.
3. All line voltage conductors must enter the cabinet on
the right side of the enclosure.
4. All low voltage conductors must enter the cabinet on
the left side of the enclosure.
5. Remove all debris and metal shavings from
the enclosure before applying power to the
ControlKeeper 4A.
ote:
N
Make certain that high voltage and low voltage
wiring enters the enclosure separately. Failure to
separate high voltage from low-voltage wiring may
cause interference with functionality. High Voltage
wiring should not be brought into the enclosure
through the left side of the enclosure.
Low voltage wiring can be brought into the enclosure
from the bottom left or upper left of the enclosure. Due
to limited space on the left side of the enclosure, it is
recommended that connections be brought through the
top or bottom of the enclosure for the low-voltage wiring.
PCI-NET TERM
REMOTE
LOCAL
50-022510-02
54-022510-
DIGIT
A
+24 GND
RS-232
PCI-NE
T
PCI-NE
T
ANALOG INPUTS
ANALOG COM
NETWORK
ALL ON
ALL OFF
POWER
RSC STAT
SWIN STAT
CAN-TX
CAN-RX
RESET PICS
LSO TEST
+24
+24
+24
+24
IN
IN
IN
IN
IN
IN
IN
IN
1
2
3
4
5
6
7
8
LS
LS
LS
LS
1
2
3
4
AN AN AN AN
1
2
3 4
DIMMING OUTPUTS
SWITCH INPUTS
VIO
1
2
3
4
GRY
1
2
3
4
ADDRESS
+NE
T
-NE
T
VIO
GRY
VIO
GRY
VIO
GRY
U2
SC1
TB7
SR1
L1
C20
PS1
L2
U20
U19
U12
TB5
U15
U16
TB4
U6
J2
J3
U7
U11
U10
U9
U1
J4
J1
J6
TB1
LED1
U5
U14
U13
TB3
S1
BR1
C39
C48
C47
C49
C40
J7
J8
REG2
REG1
SR2
TB2
J5
LED2
LED3
SW1
U8
H1
TB6
REG3
TP1
U18
U17
LED6
C29
LED7
LED5
LED4
L1 L2 L3 L4
SW3
SW2
SW1
Reset
1 2 3
4
5 6
7
8
Q4
Q3
Q2
Q1
LED9
K1
K2
K3
K4
MOV1
MOV3
MOV2
MOV4
TB1
TB2
TB3
TB4
LED1
LED3
LED5
LED7
U3
U2
U1
SW1
SW2
SW3
SW4
U4
PCI 2005
C
X4 SR
C
ST
ATUS
50-022110-01
LINE
LO
AD
LINE
LO
AD
LINE
LO
AD
Figure 1: ControlKeeper-4 Enclosure
Bring Low Voltage in
through the Left Side of
the Enclosure
Bring High Voltage in
through the Right Side
of the Enclosure
Содержание Greengate ControlKeeper CK4A-SLRC
Страница 33: ......
