background image

 

ExoCab34 outdoor cabinet 

User and Installation Guide 

 
 

©Eaton Corporation 2018. All rights reserved. 

Revision 0.1 

Page 10 of 35 

 

3.3

 

Thermal Overview 

This overview shows key points for the various cooling options. 
Please refer to product data for temperature and power ratings for each option. 
 

Standard 

 

 
The 

Standard 

option provides a fully sealed cabinet with a 

maximum level of equipment protection. 
Internal air is circulated by equipment fans. 
Heat is dissipated through the cabinet wall. 

Advantages include; 

 

Low cost  

 Zero 

maintenance 

 

High degree of protection from environmental 
contaminants 

 

Recommended for low power equipment, including 
equipment needing a high level of protection. 

 

Internal temperature is always above outside 
temperature. Ensure equipment is rated for the full 
range of internal temperatures. 

Vented 

 

 
The 

Vented

 option allows a higher heat dissipation than the 

Standard option by drawing outside air through the enclosure. 

Characteristics include; 

 

Low cost  

 

Air filter provides some protection against 
environmental contaminations.  

 

The filter requires periodic cleaning and replacement. 

 

Recommended for clean environments or with 
hardened  equipment. 

 

Internal temperature is close to ambient. 

Heat exchanger 

 

 

The 

Heat Exchanger

 option provides a cost-effective 

enclosure providing full environmental protection and an 
increased power rating compared to the Standard option. 

Characteristics include; 

 

High degree of protection from environmental 
contaminants 

 

Internal temperature is always above outside 
temperature. Ensure equipment is rated for the full 
range of internal temperatures. 

 

Low energy cost and minimal maintenance. 

 

Air conditioner 

 

 
The 

Air conditioner 

option provides a fully sealed cabinet 

with a maximum level of equipment protection. 
The air conditioner provides a stable internal temperature and 
high power dissipation rating. 

Characteristics include; 

 

High degree of protection from environmental 
contaminants 

 

Recommended for any equipment, including 
equipment needing a high level of protection and 
equipment with a restricted temperature rating. 

 

Internal temperature is maintained at a stable level. 

Содержание ExoCab34




































Отзывы: