background image

- 4 - 

#3: See life curves (below) 

Con tact C urren t(A)

20

0.5

0.1

0.2

30

50

0.3

0.7

1

2

200

300

500

100

1,000

2,000

3,000

O

p

e

ra

ti

o

n

(X

1

0

)

3

120VAC Resistive
30VDC Inductive(t=7ms)

240VAC Inductive(cos

0.4)

ψ

=

120VAC Inductive(cos =0.4)

ψ

30VDC 
Inductive
    (t=40ms)

 

 Installation 

Please install the ELCM in an enclosure 
with sufficient space around it to allow heat 
dissipation, as shown in the figure. 

 

DIN Rail Mounting:

 When mounting the 

ELCM to 35mm DIN rail, be sure to use 
the retaining clip to stop any side-to-side 
movement of the ELCM and reduce the 

 

chance of wires becoming loose. The retaining clip is at the bottom of the 
ELCM. To secure the ELCM to DIN rail, pull down the clip, place it onto 
the rail and gently push it up. To remove the ELCM, pull the retaining clip 
down with a flat screwdriver and gently remove the ELCM from DIN rail. 

 Wiring 

1.  Use 12-28 AWG single-core bare wire or multi-core (stranded) wire for 

the I/O wiring. The ELCM terminal screws should be tightened to 4.75 
kg-cm (4.12 in-lbs) and please use 60/75°C copper conductor only. 

2.  DO  NOT  wire  empty  terminals.  DO  NOT  place  input  signal  wire  and 

output power wire in the same wiring circuit. 

3.  DO NOT drop tiny metallic conductor into the ELCM while installing the 

controller or other equipment.   

 

Please attach the dustproof sticker to the ELCM before installing the 
controller or other equipment to prevent conductive objects from 
dropping in. 

 

Tear off the sticker before running the ELCM to ensure proper 
ventilation. 

 I/O Point Serial Sequence 

40-point ELCM-PH series controllers start their input expansion addressing 
from X30 and output expansion addressing from Y20. Other modules start 
their input expansion addressing from X20 and output expansion 
addressing from Y20. The expansion I/O addresses are defined in groups 
of 8. Modules with fewer than 8 I/O points will be regarded as 8. See the 

Содержание ELCM Series











Отзывы: