background image

20 

 

Replace batteries with the same number and same type of batteries.         

 

Do  not  replace  the  battery  individually.  All  the  batteries  should  be 
replaced  at  the  same  time  following  the  instructions  of  the  battery 
supplier. 

 

Normally,  the  batteries  should  be  charged  and  discharged  once 
every  4  to  6  months.  Charging  should  begin  after  the  UPS  shuts 
down  automatically  in  the  course  of  discharging,  the  standard 
charging time for the standard UPS should be at least 12 hours. 

 

5. Notes for battery disposal and battery 

replacement 

1)  Before  disposing  of  batteries,  remove  conductive  jewelry 

such as necklace, wrist watches and rings. 

2)  If it is necessary to replace any connection cables, please 

purchase  the  original  materials  from  the  authorized 
distributors  or  service  centers,  so  as  to  avoid  overheat  or 
spark resulting in fire due to insufficient capacity. 

3)  Do not dispose of batteries or battery packs in a fire, or they 

may explode. 

4)  Do  not  open  or  mutilate  batteries,  released  electrolyte  is 

highly poisonous and harmful to the skin and eyes. 

5)  Do  not  short  the  positive  and  negative  of  the  battery 

electrode, otherwise, it may result in electric shock or fire. 

6)  Make  sure  that  there  is  no  voltage  before  touching  the 

batteries.  The  battery  circuit  is  not  isolated  from  the  input 
potential circuit. There may be hazardous voltage between 
the battery terminals and the ground.     

7)  Even  though  the  input  breaker  is  disconnected,  the 

components  inside  the  UPS  are  still  connected  with  the 
batteries,  and  there  are  potential  hazardous  voltages. 

Содержание DX 10000L






























Отзывы: