Eaton DT400 Скачать руководство пользователя страница 6

Installation instructions

Complete Tee Connector kit includes: 

1 –  Moulded tee connector

1 –  Clamping screw

1 –  Basic insulating plug

1 –  Rubber cap

1 –  Cable adapter

1 –  Bi-metallic conductor contact

   – Silicone lubricant

   – Paper towel

   – Installation instructions

Step 1

1.  Train the cable to the desired finished position. (See 

Figure 2.) Be sure that the cable is long enough to 

permit movement of the tee connector from the 

apparatus bushing to a standoff bushing.

2.  Initially, cut the cable 100 mm past the bushing 

centerline.

ote:

N

This is the initial length of the cable to ensure that 

the screen wires are long enough to reach the 

earthing eye on the tee connector. The cable will 

be cut to its final length in a later step.

3.  Remove 435 mm of the cable sheath. 
4.  Fold the screen wires back over the sheath and 

secure them with two wraps of vinyl tape. (This step 

is optional. The vinyl tape is not included in the kit.)

5.  Position the cable to its final position and cut it 50 

mm from the centerline of the apparatus bushing. 

See Figure 3. 

Figure 2.   

100 mm

VINYL TAPE

SCREEN WIRES

INSULATION SCREEN

435 mm

 WARNING 

Hazardous voltage. All associated apparatus must be 

de-energized during installation and/or maintenance. 

Failure to comply may result in death, severe personal 

injury and equipment damage.

2

DT400/436 tee connector installation instructions

   MN650001EN   September 2014   www.cooperpower.com

Содержание DT400













Отзывы: