47556, Revision D
MAINTENANCE
To service unit: Isolate it from the process air and electric supply
using proper lockout tagout plant procedures. De-pressurize and de-
energize all sources of power.
•
Disconnect all remote airlines running to the assembly, marking
all airlines before removing. Loosen the 4 swing bolts from the
lid and remove the lid assembly with cleaning disc attached.
•
Inspect cleaning disc for excessive wear. If replacement is
required see the spare parts drawing supplied with the unit and
select the appropriate repair kit or contact Ronningen-Petter
Customer Service. Refer to instructions included with disc
repair kit.
•
Remove element by using the element removal handle
supplied with the unit (see the drawing below). Inspect element
for damage and plugging. Clean or replace as needed.
Remove lower “O” ring and clean.
•
To reassemble, flush housing removing all dirt and
contaminant. Clean and inspect all “O” rings for damage,
replace as needed. Place lower “O” ring in the bottom of the
housing making sure it lays flat and is centered on the ID of the
housing (Attach top element “O” ring as needed.) Replace
clean element in the housing with the handles up.
•
To replace the lid and cleaning disc assembly, extend the
center shaft to allow compression of the cleaning disc with the
compression pliers supplied with the unit. Place the Lid “O” ring
on the upper body flange checking to see that it is laying flat
and centered on the housing. Insert the cleaning disc in the
element and release the pliers and seat the lid double-checking
the placement of the lid “O” ring. Replace the lid bolts and
tighten.
•
Reconnect the airlines
•
Place the system back online using proper plant procedures.
For maintenance of other items such as lid seals, actuators, and
valves, see instructions supplied with repair kits.
EATON Filtration, LLC
9151 Shaver Road
Portage, Michigan 49024-6798 USA
Phone (Worldwide) +1 269 323 1313
Phone (U.S.) +1 800 656 3344
Fax +1 269 323 2403
Email [email protected]
www.filtration.eaton.com
SEALS
45695
45696
45697
ELEMENT
45693
EPT
45803
O-RINGS
45801
45802
VIT
BUN
MAT'L
LID
45691
45692
ELEMENT
BUN
VIT
EPT
BUNA
VITON
EPT
0.001"
63088
63063
63062
63061
63060
63067
63066
63065
63064
63077
0.015"
0.045"
0.030"
0.024"
0.0015"
0.009"
0.003"
0.004"
0.006"
0.002"
63087
P/N
DEFINED PORE SIZES
RETENTION
750
0.030"
45778
6250
3125
1550
(MICRON)
1125
PERFORATED ELEMENT SIZES
0.125"
42670
0.250"
42663
0.045"
RETENTION
0.062"
42662
P/N
45780
15
0.0006"
45771
100
25
75
50
38
380
610
200
175
230
150
0.006"
45776
0.009"
0.007"
0.008"
0.024"
0.015"
45777
47339
46261
45779
45789
0.0015"
0.002"
0.003"
0.001"
0.004"
45773
45774
45775
40667
45772
(MICRON)
SLOTTED ELEMENT SIZES
RETENTION
P/N
BUN, VIT, EPT
SLOTTED OR
PERFORATED
DEFINED PORE
(MICRON)
75
100
150
230
380
610
760
1140
38
25
50
TFE
*N/A
*N/A
*N/A
BUNA
VITON
EPT
ASSY
CLEANING DISC
KYNAR
46743
URETHANE
46608
TFE
MAT'L
UHMWPE
46741
46742
46681
40706
46680
46744
REP. KIT