manualshive.com logo in svg

Eaton Cutler-Hammer Magnum Digitrip 220+, Инструкция по эксплуатации

Поделиться
Скачать
Eaton Cutler-Hammer Magnum Digitrip 220+ Скачать руководство пользователя страница 29

Effective 7/1/2003

Page 29

I.L. 70C1037H04

interior of the breaker cell door or another visible location.

Figure 8.3 provides a place for recording test data and

actual trip values.

Ideally, sheets of this type should be used and maintained

by those personnel in the user’s organization that have the

responsibility for protection equipment.

9.0  REFERENCES

9.1  Magnum and Magnum DS Circuit Breakers

I.B. 2C12060

Magnum DS Breaker Instructions

I.B. 2C13060

Magnum I. Breaker Instructions

4A36346

Zone Interlocking Application with Non-

Magnum Breakers

I.L. 66A7508

Instruction for mMINT Modbus Translator

Module

9.2  Time-Current Curves

The Time-Current Curves are listed below for particular trip
unit models. All protection function time-current settings
should be made following the recommendations of the
specifying engineer in charge of the installation.

70C1009

  Digitrip 220 (LI) Curve

70C1295       Digitrip 220+ (L) Curve
70C1296       Digitrip 220+ (I) Curve
70C1006

  Digitrip 520 (LS) Curve

70C1007

  Digitrip 520 (I) Curve

70C1008

  Digitrip 520 (G) Curve

7.0  FRAME RATINGS (SENSOR RATINGS AND RATING PLUGS)

The frame rating

 

of a circuit breaker is the maximum RMS

current it can continuously carry. The maximum short-

circuit current rating of the circuit breaker is usually related

to the frame rating as well.

A current value, (

I

n), that is less than the full frame rating

may be chosen to be the basis for the coordination of the

protection function of the breaker without affecting its

short-circuit current capability. For the Digitrip 520 family of

trip units, this is implemented by changing the current

sensors

 

and the corresponding

 

rating plug. These sensors

and rating plugs are available in kit form.

The current sensor rating is the maximum current the

circuit breaker can carry with the specified current sensors

installed. The sensor rating can be the same or less than

the frame rating, but not greater.

This value, (

I

n), is the basis for the trip unit current set-

tings:

1. The Instantaneous and Ground Current Settings (if

provided) are multiples of (

I

n) (see Sections 4.6

and 4.7).

2. The Long Delay Current Setting, (

I

r), is a fractional

multiple of (

I

n): Long Delay Current Setting = (

I

r) = LD

x (

I

n) (see Section 4.2).

3. The Short Delay Current Setting is a multiple of (

I

r):

Short Delay Current Setting = SD x (

I

r) = SD x [LD x

(

I

n)] (see Section 4.4).

  CAUTION

BEFORE YOU FIT THE RATING PLUG INTO THE TRIP

UNIT, BE SURE TO CHECK THAT EACH BREAKER

POLE SENSOR RATING MATCHES THAT PRINTED ON

THE RATING PLUG DOOR. INSTALLING A RATING

PLUG THAT DOES NOT MATCH THE SENSOR RATING

CAN PRODUCE SERIOUS MISCOORDINATION AND/OR
FAILURE OF THE PROTECTION SYSTEM.

NOTE:

Rating plugs from Digitrip models 210, 500, or 510

CANNOT

 be used with 520 family model Trip Units.

8.0  RECORD KEEPING

Use the forms shown in Figures 8.1 and 8.2 for record

keeping. Fill in these forms, giving the indicated reference

information and initial time-current trip function settings. If

desired, make a copy of the form and attach it to the

Courtesy of NationalSwitchgear.com

Содержание Cutler-Hammer Magnum Digitrip 220+









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды