Eaton APS12-300 Series Скачать руководство пользователя страница 66

Страница: 66 / 120

Access Power Solutions Installation and Operation Guide (APS6-300/500 and APS12-300 Series)

IPN 997-00012-49G May 2013

Replacing or Adding a Rectifier

Rectifiers can be replaced without switching off the dc power system and disconnecting the
equipment it powers.





To reduce the risk of electric shock and maintain optimum system cooling, always cover
empty rectifier slots with blanking panels.



To avoid electric shock do not place hands inside the rectifier shelf.



Do not attempt to disassemble faulty rectifiers. Return them (in their original packaging)
with a completed Equipment Incident Report on page

105

Removing a Rectifier

Step 1 - Undo the rectifier retaining screw

This will release the rectifier from its rear connector.

Step 2 - Pull out the rectifier





The rectifier may be hot, especially after prolonged operation. Use suitable
gloves.

Step 3 - Replace rectifier or fit blank panel

Insert a replacement rectifier into the empty slot (see details in following section), or
fit a blank panel.

Procedure complete

Содержание APS12-300 Series


















































































































Результаты поиска

Содержание APS12-300 Series

Отзывы:

Похожие инструкции для APS12-300 Series

Бренды по названию

Популярные бренды

Eaton APS12-300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание APS12-300 Series

Отзывы:

Похожие инструкции для APS12-300 Series

Бренды по названию

Популярные бренды