Eaton 9910 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 50

Eaton 9910 Скачать руководство пользователя страница 26

INSTALLATION

Eaton 9910 UPS and EBM Installation Guide (6000 VA Models)

S

P-164000007 Rev 1

18

S

Plan the device installation starting from the bottom of the rack
cabinet. Install the heaviest device in the bottom of the rack cabinet.

S

Do not extend more than one device out of the rack cabinet at the
same time.

S

Connect all power cords to properly wired and grounded electrical
outlets.

S

Do not overload the power outlet when you install multiple devices in
the rack cabinet.

UPS Rear Panels

NOTE

The shaded areas shown in the following figures indicate the load segment

groupings. The shading does not appear on the cabinet.

A

L6

−

30P

Input plug

Fan

Ground

screw

REPO

Communication

bay

USB

connector

RS

−

232

connector

Two NEM L6

−

30R

receptacles

(Load segment 2)

EBM connector

Output

circuit breakers

Four IEC 320

−

C19

receptacles (Load segment 1)

Figure 1. The 9910-E66 UPS Rear Panel

«
...
24
25
26
27
28
...
»

Содержание 9910



















































Отзывы:

Нет отзывов