Eaton 5PX EBM 48V RT2U Скачать руководство пользователя страница 3

Page 3

614-03797-00_EN

ENGLISH

Special Symbols

The following are examples of symbols used on the UPS or accessories to alert you to important  

information:

RISK OF ELECTRIC SHOCK

 - Observe the warning associated with the risk of electric shock symbol.

Important instructions that must always be followed.

Do not discard the UPS or the UPS batteries in the trash.  

This product contains sealed lead acid batteries and must be disposed as it's explain in this manual. 

For more information, contact your local recycling/reuse or hazardous waste center.

This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE)  

in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Information, advice, help.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS. This manual contains important instructions  

that should be followed during installation and maintenance of the UPS and batteries.

The 5PX models that are covered in this manual are intended for installation in an environment  

within 0 to 40°C, free of conductive contaminant.

This equipment has been tested and found to comply with the limits for a Class A digital device,  

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a commercial environment. This equipment 

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance 

with the instruction manual, may cause harmful interference to radio communications. Operation of 

this equipment in a residential area is likely to cause harmful interference in which case the user will  

be required to correct the interference at his own expense.

Certification Standards

UPS directives: UL 1778 4

 

p

th

 edition (UL listed).

Performance: IEC 62040-3: 2001.

 

p

Radiated emission: FCC CFR 47 part 15 subpart B, Class A.

 

p

Surges withstand ability: IEEE ANSI C62.41 Category A2 (UL Listed).

 

p

Содержание 5PX EBM 48V RT2U


























Отзывы: