background image

 

 

White   

left channel L+ 

 

Red 

 

right channel R+ 

 

Green   

right channel R- 

 

Blue   

left channel L- 

 

For correct cartridge alignment, use the two-point cartridge alignment protractor provided with 

your Prelude accessories. If unfamiliar with two-point setup, please refer to your dealer. 

 

b)

 

Counterweight installation, Vertical Tracking Force setting (VTF) 

The 

counterweight (6)

 supplied is suitable for cartridges weighing between 7 - 11g. 

Pushing  carefully,  turn  the  counterweight  onto  the  rear  end  of  the  tonearm  tube  (7),  so  that 

the 

downforce  scale  (10)

  shows  towards  the  front  of  the  player.  Lower  the  tonearm  lift  and 

position  the  cartridge  in  the  space  between  tonearm  rest  and  platter.  Carefully  rotate  the 

counterweight  until  the  tonearm  tube  balances  out.  The  arm  should  return  to  the  balanced 

position  if  it  is  moved  up  or  down.  This  adjustment  must  be  done  carefully.  Do  not  forget  to 

remove the cartridge protection cap if fitted. 

Once the arm is correctly balanced return it to the 

tonearm rest (12)

. Hold the counterweight 

without moving it, and gently revolve the downforce scale ring until the zero is in line with the 

anti-skating stub (8).

 Check whether the arm still balances out. 

Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according 

to the cartridge manufacturer's recommendations. One mark on the scale represents 1 mN (= 0.1g 

/ 0.1 Pond) of downforce. 

 

Please note: Adjust the downforce prior to installing the anti-skating weight. 

The recommended downforce for the factory fitted cartridge Ortofon 2M RED is 

18mN

 

c)

 

Tonearm output connection 

Connect the tonearm cable provided with the accessories to the RCA tonearm output that is 

located at the rear  of the turntable, behind the tonearm. Connect the grounding cable on the 

earth connection screw. 

Содержание Prelude
















Отзывы: