EasyWater Toxin Shield+ TS+1000 Скачать руководство пользователя страница 3

Страница: 3 / 11

Toxin | Installation & Service Manual

Unpacking & Inspection

Basic Guidelines

Be sure to inspect the entire shipment immediately upon receipt for any shipping damage or parts
loss. Also note any damage to the shipping carton.

Contact the transportation company for all

damages and loss claims. EasyWater is not responsible for damages in transit.

Before you begin installation, read the entire manual.

CHECK LOCAL PLUMBING AND ELECTRICAL CODES. THE INSTALLATION MUST
CONFORM TO STATED CODES.

Use only lead-free solder and flux for all sweat-solder connections, as required by state and
federal codes.

Use care when handling the filter. Do not drop or set on sharp objects.

Do not locate the system where freezing temperatures occur. Do not attempt to treat water that
is over 120°F.

FREEZE DAMAGE OR HOT WATER DAMAGE VOIDS THE WARRANTY.

If installing outdoors, protect from direct sunlight. Excessive sun and heat may cause distortion
or other damage to non-metallic parts.

While the electronic components, protect the filter if installing it outdoors where water damage
can occur.

Unplug the filter from electrical power before servicing the filter or removing the outer valve
cover. Complete maintenance or repairs and replace covers before plugging into the power
outlet again.

The filter works on 120V – 60 Hz electrical power only.

MAKE SURE THE FILTER IS PLUGGED

INTO AN OUTLET WITH CONTINUOUS POWER.

Содержание Toxin Shield+ TS+1000












Результаты поиска

Содержание Toxin Shield+ TS+1000

Отзывы:

Похожие инструкции для Toxin Shield+ TS+1000

Бренды по названию

Популярные бренды

EasyWater Toxin Shield+ TS+1000, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Toxin Shield+ TS+1000

Отзывы:

Похожие инструкции для Toxin Shield+ TS+1000

Бренды по названию

Популярные бренды