2
Eastwood Technical Assistance: 800.343.9353 >> [email protected]
To order parts and supplies: 800.343.9353 >> eastwood.com
11
The
EASTWOOD-DESIGNED VERSA-CUT 60 PLASMA CUTTER
is your smartest choice for making clean, fast cuts through steel, stainless or aluminum as thin
as 24-gauge, or as thick as 7/8”. Compared to mechanical cutting, our Versa-Cut 60 Plasma Cutter works significantly faster, and makes curved and intricate
cuts more easily and precisely. A built in pilot arc system allows for instant arc striking and ease of use when cutting rusty material and expanded metal.
The internal moisture separator helps to ensure clean dry air gets to the torch to give you consistent results.
SPECIFICATIONS
DUTY CYCLE
The rated Duty Cycle refers to the amount of cutting that can be done within an amount of time. It is easiest to look at your cutting time in blocks of 10 Minutes
and the Duty Cycle being a percentage of that 10 Minutes. If cutting at 60 Amps with a 60% Duty Cycle, within a 10 Minute block of time you can cut for 6 Min-
utes with 4 Minutes of cooling for the cutter. To increase the duty cycle you can turn down the Amperage Output control.
Amperage
Output Range
Output Voltage
Weight
Duty Cycle
Overall
Dimensions
Electrical Input
Air Requirements
20-60 Amps
104 V
42 Lbs.
60% @ 60 A*
17.7” (450mm) x
7.5” (190mm) x
13.6” (345mm)
50-60Hz
220-240 VAC
5-7 CFM @ 60 psi
STATEMENT OF LIMITED WARRANTY
The Eastwood Company (hereinafter “Eastwood”) warrants to the end user (purchaser) of all new welding and cutting equipment (collectively called the “products”) that it will be free of
defects in workmanship and material. This warranty is void if the equipment has been subjected to improper installation, improper care or abnormal operations.
WARRANTY PERIOD:
All warranty periods begin on the date of purchase from Eastwood. Warranty Periods are listed below, along with the products covered during those warranty periods:
3 Year Warranty on Material, Workmanship, and Defects:
• Eastwood Versa-Cut 60 Plasma Cutter
Items not covered under this warranty: Electrodes, nozzles, diffuser, and external nozzle.
All other components are covered by the warranty and will be repaired or replaced at the discretion of Eastwood.
2 Years:
• All Welding Helmets.
CONDITIONS OF WARRANTY TO OBTAIN WARRANTY COVERAGE:
Purchaser must first contact Eastwood at 1-800-345-1178 for an RMA# before Eastwood will accept any welder returns.
Final determination of warranty on welding and cutting equipment will be made by Eastwood.
WARRANTY REPAIR:
If Eastwood confirms the existence of a defect covered under this warranty plan, Eastwood will determine whether repair or replacement is the most suitable option
to rectify the defect. At Eastwood’s request, the purchaser must return, to Eastwood, any products claimed defective under Eastwood’s warranty.
FREIGHT COSTS:
The purchaser is responsible for shipment to and from Eastwood.
WARRANTY LIMITATIONS:
EASTWOOD WILL NOT ACCEPT RESPONSIBILITY OR LIABILITY FOR REPAIRS UNLESS MADE BY EASTWOOD. EASTWOOD’S LIABILITY UNDER THIS WARRANTY SHALL NOT EXCEED THE
COST OF CORRECTING THE DEFECT OF THE EASTWOOD PRODUCT. EASTWOOD WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (SUCH AS LOSS OF BUSINESS, ETC.)
CAUSED BY THE DEFECT OR THE TIME INVOLVED TO CORRECT THE DEFECT. THIS WRITTEN WARRANTY IS THE ONLY EXPRESS WARRANTY PROVIDED BY EASTWOOD WITH RESPECT
TO ITS PRODUCTS. WARRANTIES IMPLIED BY LAW SUCH AS THE WARRANTY OF MERCHANTABILITY
ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY FOR THE EQUIPMENT INVOLVED. THIS WARRANTY GIVES THE PURCHASER SPECIFIC LEGAL RIGHTS.
THE PURCHASER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
TROUBLESHOOTING
PROBLEM
CAUSE
CORRECTION
Entire Unit Shuts Off
During Use, Switch is
in the “On” Position
Unit Has Overheated
The unit has overheated from exceeding the duty cycle and the internal
thermal protection circuitry has been activated. Turn the main power switch
off, wait several minutes to allow cooling then turn power switch back on.
The unit is ready for service.
Power Switch is
“On”, the Indicator
Light is Illuminated,
the Fan is Running,
However, When the
Torch Activation is
Depressed, There is No
Sound from the Pilot
ARC Igniter and There
is No Air Flow
Torch Not Receiving Power
Check all connections. A loose connection will prevent Torch activation.
Torch Tip Not Receiving Power
Check for damaged lines, Torch or Torch Tip.
Tip Not Receiving Power
Inspect the Torch Tip for damage, excessive molten material build-up or
excessive burning. Replace if necessary.
Power Switch is “On”,
the Indicator Light is
Illuminated, the Fan
is Running and When
the Torch Activation
Button is Depressed,
There is No Airflow
Through the Torch,
the Pilot ARC Igniter is
Activating, However, A
Plasma ARC Cannot be
Started
Torch Not Receiving Power
Check all connections. A loose connection will prevent Torch activation.
Torch Not Receiving Power
Check for damaged lines, Torch or Torch Tip.
Torch Tip Damaged
Inspect the Torch Tip for damage, excessive molten material build-up or
excessive burning. Replace if necessary.
Incorrect Voltage
Input voltage is too low or too high (below 110V or above 240V).
Air Pressure Too Low
Air pressure is too low or too high. Adjust to 60 PSI.
The Pilot ARC is
Spattering
Air Pressure Too High
Lower air pressure to 60 PSI or below.
Nozzle Worn
Replace the nozzle and electrode in the torch.
* Minimum Duty Cycle @ 25°C
