10
Eastwood Technical Assistance: 800.544.5118 >> [email protected]
To order parts and supplies: 800.345.1178 >> eastwood.com
7
ELECTRICAL LOADING
The following chart is provided as a guide to average power require-
ments in Watts for some of the most common electrical demand
items that may be used when operating your Eastwood gasoline
powered generator.
Select the items to be powered, add the column “Surge Watts” and
make sure the total DOES NOT exceed the capacity of the generator.
For absolute certainty, check the label on your individual appliances
for actual power requirements.
Appliance/Tool
Running
Watts
Surge Watts
(Starting)
100 Watt Light Bulb
1/3 HP Sump Pump
18 cu. ft. Refrigerator/Freezer
1/3 HP Well Water Pump
Fluorescent Lamp, 40 Watt
Space Heater
1/2 HP Garage Door Opener
40 Gallon Hot Water Heater
Microwave Oven, 1000 Watt
Electric Range (each burner)
Coffee Maker
Window Air Conditioner, 10,000 BTU
Home Furnace & Blower
Personal Computer
46” TV, LED
1/2 HP Drill
7-1/4” Circular Saw
10” Table Saw
100
800
800
1000
40
1500
480
4000
1000
1500
1500
1200
800
800
500
1000
1500
2000
100
1200
1600
2000
40
1500
520
4000
1000
1500
1500
1800
1300
800
500
1000
1500
2000
EXTENSION CORDS
Use only “W-A” or “W” designated outdoor-rated extension cords of
maximum length & wire gauge requirements to meet load demands.
Refer to chart at right.
NOTE:
Using undersized wire gauge and/or excessive cord lengths
will cause poor appliance performance or possible damage and may
trip generator breaker. Add and calculate total amperage require-
ments needed for appliances to be used. Do Not exceed total allow-
able amperage for generator and extension cords.
Cord Lengths / Required Wire Gauge
Total Amp
Demand
0’ to 50’
50’ to 100’
100’ to 150’
150’ to 200’
0 – 5
16 ga.
16 ga.
12 ga.
12 ga.
5.1 – 8
16 ga.
14 ga.
10 ga.
N/A
8.1 –12
14 ga.
12 ga.
N/A
N/A
12.1 – 15
12 ga.
10 ga.
N/A
N/A
15 – 20
10 ga.
10 ga.
N/A
N/A
CONNECTING TO ELECTRICAL LOAD
1.
With engine at operating temperature and at a stabilized speed, add the electrical load by plugging into the appropriate 120Volt AC or 220Volt AC
generator outlets located on the Front Panel.
2.
Keep all appliances turned OFF before connecting to Generator then turn them ON with Generator running.
3.
Be sure the Circuit Breaker is in the “ON” position.
NOTE:
The engine will speed up and become louder as an electrical load is applied. This is normal and the internal voltage regulator and governor are
functioning as intended.
DANGER! ELECTRICAL HAZARD! SHOCK HAZARD!
-
Keep Generator Dry.
-
Do Not
place generator in a wet area, on wet grass or near standing water.
-
Do Not
stand on wet grass, or near standing water when operating Generator.
-
Do Not
expose Generator to rain or allow to become wet. If emergency operation during storm conditions becomes necessary, the use of well secured,
open sided, minimum 8’ high, canopy-like structure is acceptable.
Do Not
remain under canopy with generator running. Be sure hands are dry before
touching generator, cords or connected appliances.
- If using Generator for emergency backup power, the Generator
MUST BE
isolated from electrical utility power grid. Failure to do so could cause
electrocution of utility workers or neighbors. Consult a licensed electrician to install specialized switching equipment when connecting to house wiring.
- Plug appliances directly into Generator outlet panel or use a heavy-duty, “W-A” or “W” outdoor-rated extension cord rated to accept the total load (in
watts or amps) equal to or exceeding the total of all power demands of appliances in use. All cords must have ground connections.
6.
Battery Tray assembly
(#30118 ONLY) (Fig F)
- Attach Angle Bracket (3) to weld-nut on underside of Battery Tray (1) with a 4mm screw
(Fig G)
NOTE:
Orient angle toward flanged side of Battery Tray.
- Attach inverted “Y” Bracket (2) to the Battery tray (two tabs on “Y” must be placed on
outside of Battery Tray side flanges) with 4mm screws and nuts with the short leg of
the “Y” toward the flanged edge of the tray
(Fig G)
.
NOTE:
Place screw heads inward
to avoid possible battery case contact.
- Attach opposite side “Y” bracket.
7.
Battery Tray attachment to Frame
(#30118 ONLY)
- Attach tabs of “Y” Brackets (2) to threaded holes in upper rail of Generator Frame with
two 4mm screws
(Fig H)
.
- Attach tab of Angle Bracket to through hole in lower rail of Generator Frame with two
4mm x 1.75” long screws and nuts
(Fig G)
.
8.
Add Battery
(#30118 ONLY)
- Place Battery (Interstate # DCM0018 or equivalent, not included) in Battery Tray with
Positive Terminal to the left.
- Place the Battery Hold-down Bracket over the upper front edge of the Battery case.
NOTE:
The angled flats of the Hold-down with holes must be angled toward the outer
edge of the Battery Tray.
- Place a “J” Bolt hook into hole of Battery Tray and the upper
threaded end through the corresponding hole in the angled flat of the Battery
Hold-down Bracket and secure with a 4mm nut
(Fig I)
.
- Repeat “J” Bolt assembly for opposite side.
9.
Attach Battery Cables
(#30118 ONLY)
- Attach Positive Battery Cable (Red + ) first then attach Negative Cable (Black – )
and secure to battery terminals.
10.
Install Fuse
(#30118 ONLY)
Place 5-Amp Blade Fuse (Included) into Fuse Holder and close tightly
(Fig J)
.
NOTE:
If you are not using the Electric Starter feature and are not installing the Battery,
Do Not
install the Fuse.
11.
Move generator to a dry, level, firm, OUTDOOR ONLY area away from any doors, windows
or building ventilation.
12.
Ground Cable (Required by many local electrical codes, check for your specific area)
- Connect a 6 Ga. copper ground wire (not included) to the Ground Terminal lug located
on the lower right of the Control Panel (“M” on # 30118 Panel, “J” on #30117 Panel).
- Attach the opposite end of the ground wire to a copper or brass grounding rod
(not included) driven at least 24” into the earth.
FIG. F
FIG. G
FIG. H
FIG. I
FIG. J
2
2
1
3
4
5
6
5 Amp
Fuse
