8
Eastwood Technical Assistance: 800.544.5118 >> [email protected]
opEration
1.
Slip the workpiece tube in place between the curved Die and Followbar then
place the U-Clamp over the outer side of the tube
(Fig 13)
. Lightly tighten the
Retainer Bolt if needed.
notE:
On thinner walled material, it may be helpful to place a small cut out
section of material being used between end of the Retainer Bolt and outer side
of workpiece tubing to avoid creating possible dents or damage.
2.
Drop the Ø 7/8" x 5-3/8" [Ø 22mm x 136 mm] Drive Pin
(M)
through the hole
in the outer die edge (closest to the U-Clamp) that aligns with one in the Drive
Link Assembly
(Fig 13)
.
3.
Place the Ratchet with the Teeth completely engaging the Drive Sleeve of
the Drive Link Assembly
(Fig 13)
.
4.
Begin exerting pressure on the Bender Handle to take up any lash and
eliminate looseness then set the Pointer to indicate “0°” on the Degree
Plate
(Fig 13)
.
pinCH HaZard!
the Eastwood High-Capacity tubing bender exerts tremendous bending and crushing forces in operation which can present a hand/
finger pinch hazard and cause potentially serious injuries in a matter of seconds. avoid moving parts while operating and wear thick,
well fitting work gloves to prevent cuts from handling sharp metal. the use of safety shoes is strongly recommended.
inJury HaZard!
it is strongly recommended to use the optional Eastwood # 21129 bender Handle for safest operation. do not use a bender Handle
Extension longer than 3’ (1 meter) long or permanent damage to the bender and or serious injury and property damage could occur.
if excessive force is required, stop work immediately and check material or tool for interference or damage. if any breakage or dam-
age to the bender occurs, do not usE until proper repairs are made.
inJury HaZard!
the Eastwood High-Capacity tubing bender was specifically designed to be operated by one person only. never have one person
operate the lever while one handles the material workpiece or serious injury could occur.
inJury & daMagE HaZard!
injury or property damage could occur from being struck by swinging bender Handle Extension or workpiece material. before begin-
ning work, be sure the surrounding work area is clear of obstructions or persons to accommodate the swing of the bender Handle
Extension or long sections of workpiece material.
daMagE HaZard!
the Eastwood High-Capacity tubing bender, as with many advanced metal working tools, requires a learning curve to become
proficient in its use. plan on using a generous amount of practice material in order to achieve a “feel” for the tool and learn what
results to expect before attempting a finished piece.
in addition, it is strongly suggested that you create a set of “templates” to be made of each size, material, thickness and degree of
bend for every type of tubing you plan to use in your project. this will save a great deal of time and material waste as you progress
through future projects.
daMagE HaZard!
workpiece material must be clean of any rust, burrs, nicks, welds or coatings before attempting to bend or interference and binding
will occur.
daMagE HaZard!
apply a minimal amount of a light lubricant to material and die surfaces to ease bending process. do not over lubricate.
inJury & daMagE HaZard!
tremendous external torque loads are placed on this tubing bender during operation. this tool cannot be operated without adequate
support or severe personal injury or property damage can occur if it should suddenly be become dislodged or moves while in use.
before beginning any work with this tool, it is absolutely necessary that it be securely bolted to a properly anchored Eastwood
#21116 bender stand or a heavy, sturdy, anchored workbench.
FIG. 13
✓
L
die
u-strap
✓
✓
✓
✓
✓
✓
die
X
M
die
pin
r
die
Follow bar
✓