Eastwood 19867 Скачать руководство пользователя страница 11

Страница: 11 / 12

To order parts and supplies: 800.343.9353 >> eastwood.com

PROBLEM

CAUSE

CORRECTION

“Dry” Material

Appearance

Gun is too far

from surface

Keep within 8” to 12”.

Material Gun

being moved

too fast over

surface

Slow down gun motion over surface.

Inlet air pres-

sure too high

Decrease gun inlet air pressure and or increase

Material flow setting.

Incorrect thin-

ner/reducer

Check Material manufacturer’s reducing/thinning

instructions.

Thin Material

Appearance

Material Gun

is too far from

surface

Keep within 8” to 12”.

Material Gun

being moved

too fast over

surface

Slow down gun motion over surface.

Inlet air pres-

sure too high

Decrease gun inlet air pressure and or increase

Material flow setting.

Incorrect thin-

ner/reducer

Check Material manufacturer’s reducing/thinning

instructions.

Spray is Sput-

tering

Gun being

tipped too far

down or up

Operate gun with Nozzle tilted no more than

45º down or up.

Nozzle or Wand

loose

Tighten Nozzle or Wand.

Gun internal

passages are

contaminated

Clean gun with suitable solvent.

Gun “Spurts”

at Initial Trig-

ger Pull Then

Evens Out

Air regulator

set too far back

in line causing

pressure build

up in air line

Customer supplied air regulator must be attached

at or closer to air inlet of gun.

TROUBLESHOOTING

Содержание 19867













Результаты поиска

Содержание 19867

Отзывы:

Похожие инструкции для 19867

Бренды по названию

Популярные бренды

Eastwood 19867, Инструкция по эксплуатации

Результаты поиска

Содержание 19867

Отзывы:

Похожие инструкции для 19867

Бренды по названию

Популярные бренды