EASTONTECH EW Series Скачать руководство пользователя

Страница: 25 / 27

EW-ECO SERIES OPERATION MANUAL

The adjustment o knife cutting position

1. Start the machine.
2. Adjustment of MAX2 knife position: the distance between two knife

blades’ noses should be around 8-10mm while the distance between
two blades’ V shape bottom points should be around 34mm.( See
Picture A)

3. Key points of attention for changing knife blades:

1.The up plane of inner left knife rack should be blow right knife

rack plane with 19mm which also should be lower than knife rack
outside frame with 4mm as shown by picture B.

2.Left gear should be higher than middle gear with 1 gear height

while the right gear should be higher than middle gear with 6 gear
heights.( See picture B)

3. Normally, the distance between two knife blades’ noses should be

around 8-10mm while the distance between two blades’ V shape
bottom points should be around 34mm.( See picture A)

4. After adjustment, insert both sides of knife rack gears into middle

axil tooth and fix the screws of both sides knife rack.

Содержание EW Series




























Результаты поиска

Содержание EW Series

Отзывы:

Похожие инструкции для EW Series

Бренды по названию

Популярные бренды

EASTONTECH EW Series, Руководство по эксплуатации

Результаты поиска

Содержание EW Series

Отзывы:

Похожие инструкции для EW Series

Бренды по названию

Популярные бренды