manualshive.com logo in svg

Eastey TT Series, Руководство пользователя

Поделиться
Скачать
Eastey TT Series Скачать руководство пользователя страница 14

14   Operation 

Operation 

 

Power 

 

With the toggle Power Switch set to the Off position, Directional Selection Switch set to 
the neutral/brake selection (BRK),  and Speed Control Dial set to minimum setting (0) 
Plug the power supply cord into a properly wired and grounded outlet. 
 

 

 
Toggle the Power Switch to the On position. The Power indicator light will illuminate. 

 

CAUTION! 

When the power is turned on keep clear of the rotating 
tabletop. 

 
Select the direction in which the table will rotate, using the Directional Selection 

 

CAUTION! 

When changing the direction of tabletop rotation, turn the 
speed down to zero-minimum and set the Directional 
Selection switch to the center BRK position and allow the 
tabletop to come to a full stop before selecting the opposite 
direction. 

 
Gradually increase  the rotation  speed using the Speed Control Dial to adjust  the 
tabletop rotation to the desired speed. 
 

DC Motor Speed Control

ON

FWD

BRK

OFF

REV

Allow
 Motor
 to Stop
 before
Reversing

Power 
Indicator 
Light 

Speed 
Control 
Dial 

Power 
On / Off 
Switch 

Directional 
Selection 
Switch 

Содержание TT Series



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды