Maintenance 73
Maintenance
WARNING:
Unless otherwise specifically stated, before
performing any adjustments, maintenance, or repairs,
power off the system, disable the power source, and do the
same for all connected equipment consistent with
logout/tagout
best practices.
See
https://www.osha.gov/control-hazardous-energy
the QR code at right using the camera app on your mobile
device.
CAUTION!
•
Shut off power and disconnect electrical connections before
cleaning or performing maintenance tasks.
•
Allow only trained personnel to service the machine or perform
maintenance.
•
Make sure machine has stopped and all parts have stopped moving
and are secure before attempting service or maintenance. Moving
parts can entangle or crush.
•
Always be aware of the cutting blade when handling or working
near the tape cartridge. Be careful to avoid contact with the tape
cutting blade.
•
Use the correct tools for the work required.
Preventative Maintenance
Once a week, check the machine for accumulation of dust and cardboard or paper
scraps that results naturally in carton erecting and handling. This dust can cause
premature excessive wear of system components or overheating of drive motors if
not removed and allowed to accumulate. Use a vacuum to remove larger
accumulations when required. Use a dry cloth or rag to remove excessive
accumulations that cannot be removed by vacuum. If necessary, the cleaning cloth
or rag can be lightly-dampened with water or diluted mild detergent. Do not spray
water or wet-wipe the machine.
If buildup of tape adhesive occurs, carefully wipe the area clean with an oiled cloth
or brush. A light film of oil will help prevent buildup of tape adhesive.
Check the condition of taper cutting blades and replace them if worn or damaged
to ensure a good cut of the tape on each case.
Check the condition of the belts and suction cups. Check for any accumulation of
paper dust or dirt that may be stuck onto surfaces, and check condition for
excessive wear or torn material. Clean or repair and replace as necessary.
Содержание ERX Series
