background image

 

166119

 

 

8/31/2006

 

46 

Option [3]- EIA-530 

Option [4]- HI-Z (Off) 
Selecting this last option turns off the Composite port interface drivers.  

4.7.2.4  Composite Link Timing Source[4] 

This menu allows selection of the source of the timing for the composite link. Clocks for all 
channels  are  derived  from  this  source. When  the  TxCE  driver  is  enabled,  it‟s  clock  input  is 
taken from the clock selected in this menu. 

Option [1] - Clock from associated RxC signal 
Selecting this option causes the system to derive all composite link timing from the composite 
interface receive clock (RxC) signal. 

Option [2] - Clock from internal oscillator  
Selecting this option causes the system to use it‟s internal oscillator to generate a composite 
timing signal at a frequency selected in the Composite Link Rate menu. 

4.7.2.5  Composite Link TxD Clock Signal [5] 

This menu allows selection of the timing signal from which to clock out transmit data. 

Option [1] – TxC 
This selects the Transmit Clock input (TxC) as the signal for clocking out transmit data. 

Option [2] – TxCE 
This selects the Transmit Clock output (TxCE or TT) as the signal for clocking out transmit 
data. 

4.7.2.6  Composite Link ExtClk/TT Clock Driver [6] 

This menu allows setting the TxCE/TT clock driver On or Off.  

Option [1] - Disable TxCE Driver 

Option [2] - Enable TxCE Driver 
When the TxCE driver is enabled, the clock source is either RxC or the internal oscillator, 
depending on the timing source selected (see subsection 4.7.2.4 above). 

4.7.2.7  Composite Link RTS Signal State [7] 

This menu allows setting the composite port RTS signal driver On or Off. 

Option [1] - RTS Off 

Option [2] - RTS On 

4.7.2.8  Composite Link Failure Holdoff Timer [8] 

This menu allows setting the time period after which a fault alarm will be declared due to a 
loss of link synchronization (SYNC).  

Option [1] - No Backup 
Option [2] – Immediate 
Option [3] -  1 second 
Option [4] -  5 seconds 
Option [5] - 10 seconds 
Option [6] - 30 seconds 

Содержание Nx8- Dual Composite MUX High-Speed 16-Port TDM...














































































Отзывы: