background image

6

Technical 

specifications

General

Dimensions (mm): 256 x 193 x 106 (H x W x D)

Wall mounting (mm): c/c 160 x 125 (H x W)

Operating temperature: -30 °C to +50 °C

Weight: 1.5 kg

Warranty: 3 years (warranty may be longer in some 

countries)

Charging

Charging power: 1.4–22 kW

6 A 1 phase – 32 A 3 phase (automatically  

adjusted in relation to available capacity)

Up to 7.36 kW at 32 A 1 phase

Up to 22 kW at 32 A 3 phase (TN grid)

Connection point: Type 2 socket (IEC 62196-2)

Number of phases: 1 or 3 (fully dynamic)

Voltage: 3 x 400 V AC/ 230 V AC (±10 %)

Mains frequency: 50/60 Hz

Built-in energy meter (±2 %)

Easee Home: Load balancing of up to 3 units per circuit

Easee Charge: Load balancing of up to 101 units per circuit

Sensors and indicators

Light strip with LEDs showing the status of the charger

Touch button for manual adjustment

Temperature sensors in all main contacts

Connectivity

Built-in eSIM (LTE Cat M1/ 2G /GPRS)

WiFi 2.4 GHz b/g/n connection

Easee Link RF

TM

Control charging via Easee app

RFID/NFC reader

OCPP 1.6 via our API

Protection

Built-in RCD for ground fault protection (30 mA AC/ 

6 mA DC) 

RCD is automatically reset by disconnecting the 

charging cable

Degree of protection: IP54 (the backplate is IP22  

without cover)

Impact resistance: IK08

Fire class: UL94

Insulation class: II

Overvoltage category III

Installation

Installation network: TN, IT and TT (detected 

automatically)

Installation circuit breaker: Max 40 A (Easee Home) and 

80 A (Easee Charge) overload protection. The short-

circuit current at the charging point (IkMax) must not 

exceed 10 kA. If required by the installation method, class 

A earth fault protection can be used for the circuit.

Cable cross-section: up to 16 mm

2

 (single cable)/ 

up to 10 mm

2

 (parallel connection)

Cable diameter: 8–22 mm

Terminal tightening: 5 Nm

Cable strip length: 12 mm

Содержание Home

























Отзывы: