PHASE SHIFT
0°
180°
1
RCA
XLR
SPK
2
RCA
XLR
SPK
GAIN 1
GAIN 2
PHASE DELAY
0
20ms
SUBSONIC
EQUALIZER
ON
OFF
ON
OFF
20Hz
-6dB
+6dB
30Hz
-6dB
+6dB
40Hz
-6dB
110-120VAC
ON
+6dB
OFF
POWER
110-120V ~ /60Hz
220-240 ~ /50Hz
600W
CROSSOVER
-40Hz
200Hz
ON
BY PASS
AUTO
IR INPUT
220-240VAC
POWERED SUBWOOFER
CAUTION
VORSICHT
V O R D E M Ö F F N E N
NETZSTECKER ZIEHEN
BEFORE OPENING
PULL MAIN PLUG
back of typical
processor/receiver
LEFT SUBWOOFER
RIGHT SUBWOOFER
LEFT
LEFT SUR
CENTER
RIGHT
RIGHT SUR
SUB
MAIN AUDIO OUTPUTS
PHASE SHIFT
0°
180°
1
RCA
XLR
SPK
2
RCA
XLR
SPK
GAIN 1
GAIN 2
PHASE DELAY
0
20ms
SUBSONIC
EQUALIZER
ON
OFF
ON
OFF
20Hz
-6dB
+6dB
30Hz
-6dB
+6dB
40Hz
-6dB
110-120VAC
ON
+6dB
OFF
POWER
110-120V ~ /60Hz
220-240 ~ /50Hz
600W
CROSSOVER
-40Hz
200Hz
ON
BY PASS
AUTO
IR INPUT
220-240VAC
POWERED SUBWOOFER
CAUTION
VORSICHT
V O R D E M Ö F F N E N
NETZSTECKER ZIEHEN
BEFORE OPENING
PULL MAIN PLUG
LEFT/RIGHT inputs
on the amp powering the
LEFT/RIGHT speakers/channels
LEFT
RIGHT
INPUT
Specifications are subject to change without notice.
Supernova MKVI & MKVII Manual 11
Connecting Your Subwoofer(s)
Be reminded that INPUT 2 is a dedicated LFE input
designed to accept low frequency / low pass (already
crossed) signal from processor or receiver.
Therefore, if the processor/receiver has a SUB out,
use INPUT 2 of the subwoofer.
Typically one RCA can feed enough signal to drive
the IQ amplifier to its full potential. However, in some
cases where the signal is too low for the IQ amp to
produce its full output, you may use a “Y” connector to
increase the amp’s sensitivity.
SINGLE SUBWOOFER SETUP
DUAL SUBWOOFER STEREO SETUP
back of typical
processor/receiver
LEFT
LEFT SUR
CENTER
RIGHT
RIGHT SUR
SUB
MAIN AUDIO OUTPUTS
PHASE SHIFT
0°
180°
1
RCA
XLR
SPK
2
RCA
XLR
SPK
GAIN 1
GAIN 2
PHASE DELAY
0
20ms
SUBSONIC
EQUALIZER
ON
OFF
ON
OFF
20Hz
-6dB
+6dB
30Hz
-6dB
+6dB
40Hz
-6dB
110-120VAC
ON
+6dB
OFF
POWER
110-120V ~ /60Hz
220-240 ~ /50Hz
600W
CROSSOVER
-40Hz
200Hz
ON
BY PASS
AUTO
IR INPUT
220-240VAC
POWERED SUBWOOFER
CAUTION
VORSICHT
V O R D E M Ö F F N E N
NETZSTECKER ZIEHEN
BEFORE OPENING
PULL MAIN PLUG
back of typical
processor/receiver
LEFT
LEFT SUR
CENTER
RIGHT
RIGHT SUR
SUB
MAIN AUDIO OUTPUTS
PHASE SHIFT
0°
180°
1
RCA
XLR
SPK
2
RCA
XLR
SPK
GAIN 1
GAIN 2
PHASE DELAY
0
20ms
SUBSONIC
EQUALIZER
ON
OFF
ON
OFF
20Hz
-6dB
+6dB
30Hz
-6dB
+6dB
40Hz
-6dB
110-120VAC
ON
+6dB
OFF
POWER
110-120V ~ /60Hz
220-240 ~ /50Hz
600W
CROSSOVER
-40Hz
200Hz
ON
BY PASS
AUTO
IR INPUT
220-240VAC
POWERED SUBWOOFER
CAUTION
VORSICHT
V O R D E M Ö F F N E N
NETZSTECKER ZIEHEN
BEFORE OPENING
PULL MAIN PLUG
When using only one (1) input, it takes a 250mV signal to fully power the amplifier. When signal
is fed to both inputs at the same time, the amplifier required nearly half (1/2) the signal voltage
to fully power up.
This same wiring configuration can be duplicated for the XLR inputs. However, we do
not
recommend mixing input types even though we provide you with three (3) different input types.
NOTE:
