background image

BASS CONTROLS

The WIDE knob adjusts how wide of a frequency range the MB1 will 
affect.  The  SWEEP  knob  allows  you  to  pick  the  center  frequency 
(between 27Hz and 63Hz) that you want the MB1’s restoration circuit 
to maximize. 

POWER INDICATOR

Indicates that all the wires are properly connected. If it does not light 
up, please check all wiring.

BALANCED INPUTS

Designed  to  handle  very  high  signal  voltage  up  to  15  Volts,  these 
balance inputs also help minimize feedback.

4

All specifications are subject to change without notice.

www.earthquakesound.com

1

2

3

OUTPUT CONNECTIONS

These RCA connectors should be connected to the next component 
after the MEGA BASS, such as a crossover, equalizer or amplifier.   
    NOTE: The MB1 should be in line before a crossover.

DASH INPUT CONTROL

This allows you to connect the MB1’s remote control knob. You can 
mount  the  knob  anywhere  you  want.  However,  it  is  commonly 
mounted in the front of the vehicle.
   NOTE: The remote control knob 

must be

 connected for the MB1 

to operate properly.

POWER CONNECTIONS

This  connector  allows  you  to  connect  the  Ground  and  Remote 
TURN-ON signals to the MB1. Carefully remove the connector. In a 
well lit area, properly connect all the wires. Once you decide the 
mounting location of the MB1, plug the connector back  to the MB1.

4

5

6

MB1 OVERVIEW - EXTERNAL

2

1

3

4

5

6

Digital Bass Synthesizer

Содержание MEGA BASS MB1













Отзывы: