OPERATOR INSTRUCTIONS ANd PARTS
Front Tine Models 3310V
Page 10
GetEarthquake.com
800-45-6007
FIGURE 7
OPERATION
PRE-START INSPECTION
1. Make sure all safety guards are in place and all nuts and
bolts are secure.
2. Check oil level in engine crankcase. See your engine
manual for procedure and specifications.
3. Inspect air cleaner for cleanliness. See your engine
manual for procedure.
4. Check the fuel supply. Fill the fuel tank no closer than 1
inch from top of tank to provide space for expansion.
See your engine manual for fuel recommendations.
5. Be sure spark plug wire is attached and spark plug is
tightened securely.
6. Check position of wheels.
7. Check depth regulator lever position.
8. Examine underneath and around engine for signs of oil
or fuel leaks.
9. Inspect fuel hoses for tightness and fuel seepage.
10. Look for signs of engine damage.
11. Remove excessive debris from muffler area and recoil
starter.
START-UP
The controls required to start and run the rototiller are located
on the handlebar.
A more detailed description of engine operation and all
related precautions and procedures can be found in the
engine manufacturer’s manual that accompanies each
tiller.
COLd STARTS
1. Move throttle lever to full choke position.
SEE FIGURE
7.
2. Pull starting rope out slowly one time and allow to return
normally.
3. Pull starting rope out rapidly, and allow rope to return
normally.
4. When engine starts, gradually move choke lever to run
position and increase throttle speed to “FAST” position.
RESTARTING A WARM ENGINE
Restarting an engine that is already warm from previous
running does not normally require use of the choke.
1. Move throttle lever to run fast position.
2. Pull starting rope out rapidly until engine starts. Allow
rope to return normally. Repeat until engine starts.
GASOLINE IS hIGhLY FLAMMABLE ANd MUST
BE hANdLEd WITh CARE. NEvER FILL ThE TANk
WhEN ThE ENGINE IS hOT OR RUNNING. ALWAYS
MOvE OUTdOORS TO FILL ThE TANk.
TEMPERATURE OF MUFFLER ANd NEAR BY AREAS
MAY ExCEEd 150
°
F. AvOId ThESE AREAS.
dO NOT MOvE ChOkE CONTROL TO ChOkE TO
STOP ENGINE. BACkFIRE OR ENGINE dAMAGE
MAY OCCUR.
TO STOP ThE ENGINE AT ANY TIME, MOvE ThROT-
TLE CONTROL TO ThE OFF POSITION. TO STOP
TINES AT ANY TIME, RELEASE dRIvE SAFETY
CONTROL LEvER TO ThE NEUTRAL POSITION.
ALWAYS RELEASE dRIvE SAFETY CONTROL
LEvER TO ThE NEUTRAL POSITION BEFORE
AdjUSTING ThE dEPTh OF ThE REGULATOR
LEvER.
IMPORTANT
ENGINE IS ShIPPEd FROM FACTORY WIThOUT OIL.
YOU MUST Add ENGINE OIL BEFORE STARTING
ENGINE.
PRACTICE OPERATING ThE CONTROLS ANd
TILLER WITh TINES OUT OF GROUNd BEFORE
BEGINNING TO TILL. IT IS IMPORTANT ThAT YOU
kNOW hOW TO USE ThE TILLER PROPERLY, kEEP
CONTROL AT ALL TIMES, STOP ThE TINES ANd
WhEELS FROM TURNING, ANd STOP ThE ENGINE
IF NECESSARY. IF YOU dO NOT kNOW hOW TO
dO ThESE ThINGS, REAd ThE CONTROLS ANd
SAFETY SECTIONS BEFORE PROCEEdING.
CAUTION
!
WARNING
!
PLEASE dO NOT START YOUR TILLER UNTIL YOU
hAvE REAd ThE MANUAL ThAT CAME WITh YOUR
ENGINE, ANd ThE SECTIONS IN ThIS MANUAL
TITLEd CONTROLS ANd SAFETY. IF YOU hAvE
REAd ThESE, FOLLOW ThE STEPS BELOW TO
START YOUR TILLER. ALWAYS PERFORM ThIS
PRE-START ChECkLIST BEFORE STARTING ThE
ENGINE.
Содержание 3310V
Страница 2: ......
