EarthCore Isokern MAXIMUS 82L120 Скачать руководство пользователя страница 15

Страница: 15 / 69

Earthcore Industries

12/2021

Isokern Maximus Linear Series Open Front Gas Fireplace

Calculating Flooring Loads

Floor framing for Maximus Linear Open Front installation will need to be designed and built to accept substantial dead loads

spread over a relatively small floor area.

(Figure 3)

The following weights and sizes can be used to calculate loading. It is the contractor’s responsibility to provide adequate

floor system load capacity.

WEIGHTS AND LOAD CALCULATIONS

Total dead load amounts include (but are not necessarily limited to) the following items and their corresponding weight

estimates as listed below:

Isokern Open Front unit weights:

Maximus Linear Open Front - 48: 1,1275 lbs. (no burner, flue, or accessories)

Maximus Linear Open Front - 72: 1,990 lbs. (includes steel angle; but no burner, flue, or accessories)

Maximus Linear Open Front - 96: 2,450 lbs. (includes steel angle; but no burner, flue, or accessories)

Maximus Linear Open Front - 120: 2,997 lbs. (includes steel angle; but no burner, flue, or accessories)

Approximate weight of glass media: 100 lbs.

Fire brick and Adhesive: 350 lbs. - 1800 lbs. depending on brick size and pattern

Facing material: per general contractor

B-Vent metal flue: per manufacturer and installation requirements

The floor area for each model is as follows:

•

Maximus Linear Open Front – 48: @ 53” x 28” = 10.3 sq. ft.

•

Maximus Linear Open Front - 72: @ 85-3/4” x 28” = 16.67 sq. ft.

•

Maximus Linear Open Front – 96: @ 108-1/4” x 28” = 21.04 sq. ft.

•

Maximus Linear Open Front – 120: @ 131-3/4” x 28” = 25.62 sq. ft.

Earthcore is not responsible for structural floor support details for this fireplace system. Unless otherwise noted all floor

framing drawings in this manual are merely illustrations to indicate the presence of an underlying floor system. Consult your

local structural engineer for proper floor system design, sizing, and specifications.

NOTE: The required noncombustible hearth

extensions not shown in this view.

Содержание Isokern MAXIMUS 82L120






































































Результаты поиска

Содержание Isokern MAXIMUS 82L120

Отзывы:

Похожие инструкции для Isokern MAXIMUS 82L120

Бренды по названию

Популярные бренды

EarthCore Isokern MAXIMUS 82L120, Инструкция по установке, эксплуатации, обслуживанию и руководство владельца

Результаты поиска

Содержание Isokern MAXIMUS 82L120

Отзывы:

Похожие инструкции для Isokern MAXIMUS 82L120

Бренды по названию

Популярные бренды