B
H
E
B
F
F
F
F
E
E
E
E
D
B
Ｘ８
H
B
F
L
Ｘ８
H
F
F
F
1
Attach the Dividers to the Top Shelf
2
Insert the Back Panels
3
Insert the Middle Shelves
4
Attach the Divider Section to
the Base
5
Attach the Wheel Casters
1A. Place the Top Shelf(B) top-down on a carpet or protected surface.
Insert 8 Metal Dowels(H) into the plastic plugs located underneath
the Top Shelf(B). Tighten with a Phillips Head Screwdriver.
1B. Insert 2 Cams(L) into the large holes in each of the Dividers(F).
Make sure the arrows on Cams(L) point toward the holes in the closest
edge.
1C. Position the Top Panel(B) so the attached Metal Dowels(H) enter the
holes in the top edge of the Dividers(F). Turn Cams(L) with a Phillips
Head Screwdriver until locked onto the Metal Dowels(H).
2. Slide the Back Panels(E) into the grooves between the Dividers(F)
until fully inserted into the slot as shown.
F
E
E
E
E
E
F
F
F
B
C1
C2
C2
3A.
Two Adults Suggested:
Carefully lay the unit down
on its back. Insert a Middle
Shelf(C2) into the bottom slots
on the Dividers(F) as shown
until fully inserted.
3B. Insert a Middle Shelf(C1)
into the middle slots on the
Dividers(F) as shown until
fully inserted.
3C. Insert a Middle Shelf(C2)
into the top slots on the
Dividers(F) as shown until
fully inserted.
G
Ｘ８
F
F
F
F
C2
C2
C1
G
B
D
F
C2
C2
C1
J
K
4A.
Two Adults
Suggested:
Carefully turn the
unit upside down to
rest on Top Shelf(B).
4B. Attach the Base
to the Divider
Section(F,E,C1,C2)
using 8 Large Hex
Screws(G). Tighten
with the Hex Key
Tool(I).
TIP
！
DO NOT FULLY
TIGHTEN SCREWS
UNTIL ALL SCREWS
HAVE BEEN LOOSELY
POSITIONED
。
!
WARNING:
-
Adult Assembly Required.
Two
adults recommended.
- Contains small parts, sharp points
and edges.
- Do not stand, sit, kneel, climb, lean
or pull on unit for support.
- Never leave children unattended.
- Do not place unit near high heat or
moisture.
- Adult Supervision Recommended.
BEFORE ASSEMBLING,
MAKE SURE THERE
ARE NO
MISSING PARTS.
A2
A1
C2
D
E
B
B
A2
A1
E
E
E
E
F
F
F
F
D
C2
C1
Mount Laurel,NJ 08054 USA
www.ecr4kids.com
Model No. ELR-0635
20-Tray Storage Cabinet
Left Side Panel
Right Side Panel
Top Shelf
Middle Shelf(1)
Middle Shelf(2)
Bottom Shelf
Back Panel(5)
Divider(4)
Large Hex Screw(20)
Metal Dowels(8)
Hex Key Tool
Wheel Casters(4)
Caster Screws(16)
Cams(8)
PARTS LIST
B
D
E
F
C2
A1
A2
C1
G
H
I
J
K
L
J
K
Ｘ４
Ｘ１６
- If the Back Panel does
not slide easily into the
grooves, wiggle the Back
while pushing the panel
into the slot.
- You may also turn the
rear Cams on the shelf
above or below to unlock,
push the Back until fully
inserted into the slot, then
turn Cams to the locked
position again.
TIP:
Version: ELR-0635.D.2010.01.04
Attach
First
Mount
Plate
Caster
Screw
5. Beginning with the holes on the inside of the Wheel Caster(J) mount
plate (opposite the kickplate on Base(D)), attach the 4 Wheel Casters(J)
using 16 Caster Screws(K). Tighten with a Phillips Screwdriver.
